554792
4
Verklein
Vergroot
Pagina terug
1/22
Pagina verder
3.2 Hard-wired inputs on the main board
There are hard-wired input terminals for 01-04 device addresses on the
main board. All hard-wired inputs act identically: double balanced loops which
sense loop stand-by, activation or tampering as follows:
stand-by connected to COM via a 1 k resistor (EOL resistor)
activation connected to COM via a 2k to 6k resistor
tampering connected to COM via a less than 700 resistor (short-
circuit) or connected to COM via a more than 6k resistor
(loop termination)
12 34
ON
OFF
01
02
COM
03
04
EW
IW
PGX
PGY
GND
A
B
+U
1k
1k
fig. 2 SA-200 magnetic detector connection
12 34
ON
OFF
01
02
COM
03
04
EW
IW
PGX
PGY
GND
A
B
+U
1k
1k
JA-82K control panel installation manual - 4 - MKH51103
fig. 3 JS-20 Largo detector connection
12 34
ON
OFF
01
02
COM
03
04
EW
IW
PGX
PGY
GND
A
B
+U
1k
1k
fig. 4 One-loop connection of JS-25 Combo
12 34
ON
OFF
01
02
COM
03
04
EW
IW
PGX
PGY
GND
A
B
+U
1k
1k
1k
1k
fig. 5 Two-loop connection of JS-25 Combo (01 GBS, 02 PIR)
12 34
ON
OFF
+U
GND
01
02
COM
03
04
fig. 6 Connection of multiple detectors to the inputs
The used input zone must be terminated by a 1k resistor in stand-by
state.
When connecting a trigger contact to the zone, always use a parallel
1k resistor. Thus it is possible to connect up to 5 trigger contacts in
series.
Tamper contacts should be connected in series (without resistors).
They therefore interrupt the whole loop. You can use an unlimited
amount of tamper contacts which can be combined with trigger
contacts (with parallel resistors).
The loop (input) reaction can be set. The NATURAL = delayed loop
reaction is set as the factory default.
If you enrol a wireless device to the hard-wired input address, the
corresponding terminal will be disabled (it will not affect the system).
If you do not intend to use the hard-wire input or enrol a wireless
device to its address, switch the corresponding DIP switch to the OFF
position (switch off the input).
3.3 Installation of additional hard-wire input
modules
By adding the JA-82C module it is possible to extend the amount of
inputs to fourteen. (addresses 01-14).
All hard-wire inputs behave identically: they are double balanced inputs
which are able to sense stand-by, activation and tampering and for which
examples of connection and conditions stated in Chapter 3.2 apply in full
scope.
When you install the module, relabel the terminal description with a
sticker from the module package (inputs 05-14). Insert plastic spacing posts
on the openings in the module on the connector side and insert the prepared
module to the selected position in the main board.
3.4 Radio module installation
The JA-82R radio module is installed in position 1 (see fig. 1). The
antenna is included in the JA-82R package and it should be screwed on a
plastic post (see fig. 17, pos 5). The antenna connector connects to the pins
on
the JA-82R module. The module installation enables the system to enroll
up to 50 wireless devices.
3.5 Y,X,V communicator module installation
Screw the selected communicator into position using the supplied
screws as shown in the picture fig. 17.
If y
ou are installing a GSM communicator (Y) and there is a strong GSM
signal in the place of installation, the self-adhesive antenna can be attached
directly to the bottom of the plastic box (see fig. 17). If there is a weak GSM
sig
nal we recommend using some of the available rod antennas.
If you use the combination of a GSM communicator (Y) and a telephone
line communicator (X), install the phone line communicator above the GSM
communicator using the supplied posts.
3.6 Control panel memory chip
The control panel memory chip plugs into its own socket. If you take the
memory unit from the control panel and plug it into another control panel main
board of the same type, the control panel settings (enrolled detectors, codes,
set functions, etc.) are transferred.
Notes:
communicator settings are not stored in this memory
do not plug or unplug the memory when the control panel is powered
when you take the memory unit from a damaged control panel, its
contents may be corrupted. It is therefore highly recommended to
back-up the settings in a PC using OLink software
3.7 Wired keypad connection
The control panel can be operated and programmed by a JA-81E hard-
wired keypad. A screened four-cord flat cable connecting the corresponding
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron JA-82K OASIS bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron JA-82K OASIS in de taal/talen: Engels als bijlage per email.

De handleiding is 0,66 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Jablotron JA-82K OASIS

Jablotron JA-82K OASIS Installatiehandleiding - Deutsch - 23 pagina's

Jablotron JA-82K OASIS Gebruiksaanwijzing - English - 23 pagina's

Jablotron JA-82K OASIS Aanvulling / aanpassing - English - 1 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info