554792
5
Verklein
Vergroot
Pagina terug
1/22
Pagina verder
terminals should be used for permanent connection between the keypad and
the control panel (see
fig. 7.)
The keypad can also be connected to a bus connector on the control
panel box using a flat cable (max 10 metres) with RJ connectors for the
purpose of servicing or system debugging.
JA-82K control panel installation manual - 5 - MKH51103
1 2 3
A
BC
4 5 6
A
7 8 9
ON
0 #
B
?
OFF
ESC
ABC
OASiS
1 2 3
A
BC
4 5 6
A
7 8 9
ON
0 #
B
?
OFF
ESC
ABC
OASiS
Control and programming
keypad JA-81E
Modular connection
cable
fig. 7 Wired keypad connection
Notes:
When you use the INP keypad hard-wired input to connect the door
detector, its reaction is always delayed (it triggers an entry delay) and it
is assigned to section C.
We recommend having only a single JA-81E hard-wired keypad in the
system.
3.8 Control panel resetting
If you need to set the factory-default settings in the control panel, perform
the following:
1. Disconnect the back-up battery and the mains (using the terminal
board fuse),
2. Connect the RESET link and leave it connected,
3. Connect the back-up battery and the mains,
4. Wait until the green LED starts flashing and then disconnect the
RESET link.
If you need to reset the control panel with preset parameters according to
EN 50131-3 (see 6.48) follow these next steps:
1. Disconnect the back-up battery and the mains (using the terminal
board fuse),
2. Connect the RESET link and leave it connected,
3. Connect the back-up battery and the mains,
4. Wait until the green LED starts flashing and key in the sequence
8080 an finally disconnect the RESET link.
Notes:
After a RESET, all wireless devices and access cards are erased from
the control panel as well as user codes.
The Master code changes to 1234, and the service code to 8080.
If resetting is disabled (see 6.8) it is impossible to reset the control
panel.
4 Control panel power supply
Once the control panel is assembled and all modules are in place, you
can proceed with putting the control panel into operation. We recommend
switching the control panel on without any wired detectors connected, using
only the wired keypad (if it is used in the system) for the first time. Only then
should you continue connecting the detectors. Beware of short circuits – it is
strongly recommended to switch off the power when working.
4.1 Backup battery connection
It is possible to use a 12V gel cell backup battery, with a capacity of up to
2.4 Ah in the control panel. The EN 50131-1 standard requires a 12-hour
minimum backup time in case of a power grid failure. For the standby
consumption of all system devices, see fig. 8.
ATTENTION – the backup battery is sold
charged, avoid shorting out its terminals!
The average backup battery lifetime is up to 5 years after which it must
be replaced. Checking its capacity during regular maintenance is recommended.
The control panel automatically recharges the backup battery and monitors
its condition. When the system runs only on the backup battery, the battery
status is monitored and a technical alarm is triggered before its complete
depletion. The backup battery is then disconnected. Once the power supply
has been restored, the battery reconnects and is recharged.
Ensure that the battery is correctly connected (Polarity: RED = positive +,
BLACK = negative -).
fig. 8 power consumption of individual components
4.2 Power supply connection
Only a person with corresponding electro-
technical qualification can connect the power
supply.
The control panel power supply is double-
insulated (safety class 2) and does not
incorporate a protective grounding wire.
The control-panel power cable should only be installed by a person
holding a sufficient electro-technical qualification.
The control panel power supply is double-insulated (protection class II)
and does not incorporate a protective earth wire.
A double-insulated power cable should be used with a minimum cross-
sectional area of 0.75 to 1.5 mm2. The power cable should be
connected to a switched mains supply fused to 10 Amps.
In the control panel, connect the cable to the power terminals equipped
with a fuse of type T200mA/250V.
Fix the cable firmly to the cable holder in the control panel making
sure that the wire ends are properly secured and connected in the
terminals.
Mains fuse
T 200 mA
4.3 Powering-up the control panel for the first time
1. First check all the wiring, and if a GSM communicator is installed, insert its
SIM card (PIN code disabled).
2. Check the backup battery connection
3. Switch the power supply on – a green LED starts flashing on the control panel
board.
4. If a hard-wired keypad is connected it indicates “Service” mode
5. The control panel can also be set up via the interface using OLink software
(A virtual keypad can be used in OLink to indicate system status).
6. If you have neither the wired keypad, nor OLink, enrol a wireless keypad by
the following means:
a) have an opened keypad and its battery ready,
b) check that the green LED in the control panel is flashing,
c) short the RESET link in the control panel for 1 second (enrollment
mode opens),
d) install batteries into the keypad not far from the control panel
e) the keypad emits a beep and enrols to the first free address. After
that it displays “Enrollment” and offers another free address for
enrollment
device mA note
JA-82K control panel 30 without a communicator
JA-82R module 20
JA-82C module 15
JA-81E keypad 30
JA-81E RGB keypad up to 100
JA-80H (N) keypad 60 including WJ-80 interface
JA-8xY communicator 35
JA-80V communicator 30
JA-80X communicator 15
Wireless devices are not powered from the control panel
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron JA-82K OASIS bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron JA-82K OASIS in de taal/talen: Engels als bijlage per email.

De handleiding is 0,66 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Jablotron JA-82K OASIS

Jablotron JA-82K OASIS Installatiehandleiding - Deutsch - 23 pagina's

Jablotron JA-82K OASIS Gebruiksaanwijzing - English - 23 pagina's

Jablotron JA-82K OASIS Aanvulling / aanpassing - English - 1 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info