554835
4
Verklein
Vergroot
Pagina terug
1/22
Pagina verder
Installation manual: Oasis security system JA-80K - 4 - MKE51801
sent to alarm receiving centres (central monitoring stations).
They can notify the user using SMS reports and allow remote
control and programming of the system by mobile phone and
the Internet. Another option is the JA-80X communicator
which reports alarms via a traditional phone line using voice
messages.
Note: The Oasis JA-80 system has three modes: operating
mode, maintenance mode and service mode. Operating
mode is for the day-to-day use of the system by all authorised
users, e.g. setting/unsetting (arming/disarming). Maintenance
mode is for the holder of the master code (system administrator)
to have limited programming of the system, e.g. changing
codes/cards, bypassing and is inaccessible to all other users.
Service mode is only for installers and is used to program and
control all aspects of the system.
1.1. Optional system configurations
In the European Union region, follow the valid standards and
rules, especially series EN-501-xx. The Oasis control panel
complies with grade 2.
The control panel must have one of the following configurations
as a minimum:
At least two non-backup-battery sirens (JA-80L or SA-105) +
communicator class ATS2 (JA-80Y, JA-80V or JA-80X)
At least one backup-battery siren (JA-80A or OS-360/365/300)
+ communicator class ATS2 (JA-80Y, JA-80V or JA-80X)
No siren + communicator class ATS3 (JA-80Y or JA-80V)
Note: the above-recommended configurations are based on the
EU standard EN-50131-1 valid at the time of issuing this
manual.
2. Installation
The control panel can be attached to the wall using 3 screws.
The drilling template is on the last page of this manual.
Because the control panel communicates via radio, it
should not be installed near any large metal objects
capable of shielding radio communication.
Route cables (power supplies, telephone leads etc.) inside
the control panel before tightly screwing in the screws.
2.1. Power inlet
The control-panel power cable should only be installed by a
person holding a sufficient electro-technical qualification.
Mains fuse
T 200 mA
The control panel power supply is double-insulated (safety
class 2) and does not incorporate a protective earth wire.
A double-insulated power cable should be used with a
minimum cross-sectional area of 0.75 to 1.5 mm
2
. The
power cable should be connected to a switched mains
supply fused to 10 Amps.
In the control panel, connect the cable to the power
terminals equipped with a fuse of type T200mA/250V.
Fix the cable firmly to the cable holder in the control
panel making sure that the wire ends are properly secured
and connected in the terminals.
0
1
C
O
M
0
2
N
C
N
O
E
W
-
C
I
W
P
G
X
P
G
Y
G
N
D
A
B
+
U
A
C
2
0
V
antenna connector
RESET
Communicator
connector
Wiring plug
Digital bus
1A +U
fuse for
Termi n al s fo r
transformer output
Radio
module
memory socket
3. Control panel memory unit
The control panel memory unit plugs into its own socket. If, for
example, the control panel was damaged, the memory unit could
be unplugged and then plugged into another control panel circuit
board of the same type to transfer and preserve the settings
including enrolled detectors, access codes and cards. The new
control panel thereby becomes an exact copy of the former one
(a clone).
Notes:
There are no communicator settings in this memory unit
Do not connect or disconnect the memory unit while the control panel
is powered.
Although the memory unit is well-protected, in cases of severe
damage to the control panel there is a risk that memory contents
could be corrupted. It is therefore highly recommended to back-up the
settings in a PC using Comlink software.
4. Control panel connectors and terminals
Antenna connector – This is used to connect either to an
internal antenna or to external antennas such as the AN-80 or
AN-81.
Reset link (normally open) – Used to reset the control panel by
shorting the link only while powering up the control panel. This
link can also be used to enter control panel enrollment mode by
briefly shorting the link while the control panel is powered.
Digital bus connector – for connecting a JA-80E keypad or a
PC running Comlink software with a JA-80T interface cable. The
same digital bus connector is present on the bottom right hand
corner of the plastic housing. Additionally, the same connections
are available on the GND, A, B, +U terminals.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron JA-80K bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron JA-80K in de taal/talen: Engels als bijlage per email.

De handleiding is 0,55 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Jablotron JA-80K

Jablotron JA-80K Gebruiksaanwijzing - English - 1 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info