554884
5
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
User manual JA-60GSM - 8 - MFJ51808
3.3. SMS texts editing
The list of SMS texts stored in the dialer consists of texts reported as event reports (installation
name, event name and source name) and texts for remote control instructions. All these texts can be
edited by the following SMS sent from a mobile phone.
yyyyyTXTz,text, z,text
where:
yyyyy is the remote access code; default setting is 1111; this code can be changed,
see section 4.1
TXT is the text programming command
z is the text index (110 - 711 see table 3.3.1).
, comma (separator)
text is the new text string. Neither a comma nor a dot can be used inside the text. Space
inside the text is a valid character (dialer ignores spaces out of the “text” string)
separator (asterisk or space)
Note: If you change texts of command SMS this way (texts no. 703 to 711), then you will actually
change the commands which the system reacts to. E.g.: if you change text „MO“ (text no. 705) to
„STATE OF THE ALARM SYSTEM?“ then this command can only be used to learn the status of the
system. You can change texts for your needs and also insert a password to protect against
unauthorized use of SMS commands.
Example: If the factory default code for the dialer is 1111, then the sending of SMS:
1111*TXT*201, uncle Sam’s controller, 202, aunt Mary’s controller to the dialer will change names of remote
controllers No. 1 and 2.
3.3.1. Table of SMS texts
Text index z Factory default text Text index z Factory default text
110 Master code 301 Wired detector #1
201 Controller #1 302 Wired detector #2
202 Controller #2 303 Wired detector #3
203 Controller #3 304 Wired detector #4
204 Controller #4 305 Wired detector #5
205 Controller #5 306 Wired detector #6
206 Controller #6 307 Wired detector #7
207 Controller #7 308 Wired detector #8
208 Controller #8 309 Wired detector #9
501 User code #1 310 Wired detector #10
502 User code #2 311 Wired detector #11
503 User code #3 312 Wired detector #12
504 User code #4 313 Wired detector #13
505 User code #5 314 Wired detector #14
506 User code #6 315 Wired detector #15
507 User code #7 316 Wired detector #16
508 User code #8 401 Wireless detector #1
509 User code #9 402 Wireless detector #2
510 User code #10 403 Wireless detector #3
511 User code #11 404 Wireless detector #4
512 User code #12 405 Wireless detector #5
513 User code #13 406 Wireless detector #6
514 User code #14 407 Wireless detector #7
700 Alarm system reports: 408 Wireless detector #8
703 AM 409 Wireless detector #9
704 DM 410 Wireless detector #10
705 MO 411 Wireless detector #11
706 ME 412 Wireless detector #12
707 AUXON 413 Wireless detector #13
708 AUXOFF 414 Wireless detector #14
710 PGON 415 Wireless detector #15
711 PGOFF 416 Wireless detector #16
User manual JA-60GSM - 5 - MFJ51808
2. SMS and audible alarm reports setting
The factory default settings allow the GSM dialer to send SMS reports and audible warnings when the
control panel generates important pertinent information (alarms, arming, etc.). It is only necessary to set the
telephone numbers to where the information should be reported. If you want to report additional or different
events than the factory default provides, see section 3.
The following information is for use by an alarm system administrator who knows the master code.
All settings can be programmed via a keypad. A sequence can be canceled anytime by pressing the
“N” key (e.g. entry error). When a sequence is complete, the system will store it into the memory. The
following settings are made in the user mode, which can be entered by:
F 0 master code. (this mode is indicated by the “U” character on the keypad’s LED display).
Example:
If the master code is 1234 then enter: F0 1234
Press “N” to exit the user mode.
2.1. Telephone numbers setting
The dialer has 8 telephone number memories. Each memory has particular SMS reports assigned to
it and/or audible warnings according to the default setting – see table 2.2. By entering a telephone
number to a particular memory selects what will be reported to this number:
7t xxx...x F0
where:
t is a memory from 1 to 7
xxx...x is a telephone number (max. 20 digits), enter F9 before the number, if you need
+ prefix for international calls. To use an attached SMS phone set enter code
001 instead of the telephone number
To disable reporting to a particular number, delete this number from the memory by entering:
7tF0
where:
t is a memory from 1 to 7
Report testing:
If you wish to report any alarm, arming and disarming via an SMS followed by a notifying call and your
mobile phone number is 123456789, then enter 75123456789F0 (while the control panel is in the
programming mode).
Then exit the programming mode by pressing the N key. Now when you arm the system your mobile
phone will receive a reporting SMS.
Notes:
For SMS transfers use only numbers of mobile phones or call centers that can transfer SMS
messages.
Audible warnings can be used on both GSM and landline networks.
The GSM dialer can report all event information from the alarm system via SMS and audible
warnings. The setting of reported events for all numbers can be changed – see chapter 3.
2.2. Telephone numbers table
Memory
Entering
sequence
To this pair of numbers will be sent (factory default): Telephone numbers
1. 71 ____ F0
2. 72 ____ F0
- ALARM SMS
- Technical SMS
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron JA-60GSM bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron JA-60GSM in de taal/talen: Engels als bijlage per email.

De handleiding is 0,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Jablotron JA-60GSM

Jablotron JA-60GSM Installatiehandleiding - English - 11 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info