554884
4
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
User manual JA-60GSM - 4 - MFJ51808
1.10. Alarm system remote control via a telephone keypad
If you want to operate the alarm system via a phone (mobile or landline), perform the following:
Dial the GSM dialer number. An attached telephone will ring.
If the phone is not answered the system will answer in 25 seconds - indicated by a short beep.
Enter the remote access code; factory default is 1111; to change this code see section 4.1.
Confirmation sounds indicate the control panel mode: 1 beep = armed, 2 beeps = disarmed, 3 beeps
= programming mode, Siren sound = alarm.
From this moment the telephone keypad will work as the alarm control panel keypad. Key E is
interpreted as F, key # as N.
To terminate the connection simply hang up. Connection will automatically terminate if there is no
entry within 60 seconds.
Notes:
Remote access from a landline is only possible from a phone using tone dialing (DTMF)
It is impossible to operate the system remotely without a valid remote access code (if used).
1.11. Remote controlling of an appliance via a telephone keypad
If you want to operate outputs PgX or PgY (e.g. an appliance in the house) from a phone (mobile or
landline), perform the following:
a) Dial the GSM dialer number. An attached telephone will ring.
b) If the phone is not answered, the system will answer in 25 seconds - indicated by a short
beep.
c) Enter the remote user access code; factory default setting is 1111; to change this code see
section 4.1.
d) The system will confirm the validity of the code with a beep.
e) From this moment you can operate the PgX and PgY outputs by entering:
80 - to switch off
 81 - to switch on (permanently)
f) To terminate the connection simply hang up. Connection will automatically terminate if there
is no entry within 60 seconds.
Notes:
Remote access from a land line is only possible from a phone using tone dialing (DTMF)
If the system is programmed to allow control only with a valid code the control sequence must
be complete with a user code: (8[code]0 or 8[code]1).
For using this function the alarm system must support F 81 and F 80 sequences
1.12. Remote voice communication with premises
If the SP-01 intercom is plug-in to the PHONE terminal (it must not be combined with any phone
connected) it is possible to create a one way (talking or listening) communication from an authorized
(stored) phone numbers (see 2.1.). Procedure:
a) From an authorized phone dial the JA-60GSM phone number. The SP-01 will ring once and
then it will answer the call
b) Potential alarm on the control panel will be terminated
c) You can talk to the premises
d) For switching to the listening mode press 5 on your phone. For switching back to the talking
mode press key 2. Or by pressing button 1 it is possible to toggle between talking and
listening.
e) Press 0 or hang-up to terminate the call.
Note:
Only a phone with available DTMF can be used.
User manual JA-60GSM - 9 - MFJ51808
4. General settings
Enter the user mode (see section2.) before using any of the following sequences.
4.1. Remote access code
9 4 xxxxxxxx F1
where:
xxxxxxxx is the code, it can have from 1 to 8 digits
If you enter 94F1 - the code is erased and the remote access to the alarm system is not allowed.
Default setting: 1111
4.2. One-time dialing-in when in user mode
While the control panel is in the user mode, you can enable one-time remote access by entering 970. After
entering this code the dialer responds to the first ring of any incoming call. The access code is not requested,
so the calling phone keypad can be immediately used as the keypad of the alarm system (* = F, # = N).
The immediate dialing-in will be disabled after you dial-in or after you exit the programming mode.
4.3. GSM signal monitoring
The proper function of the GSM dialer is conditional on the GSM signal being strong enough. Enter
971 to measure the GSM signal level. The keypad’s display shows a number from 0 to 9 and it beeps
every second indicating a new measurement. For proper functioning of the module the signal level
should be 3 or higher. Find the best location for the antenna while measuring the signal level.
To switch the system back to the user mode press the N key.
4.4. Attached phone function
The dialer provides a PHONE output to connect an ordinary telephone set. The function of this
telephone can be modified by entering:
98 y
where function
y = 0
ordinary telephone line is simulated, it is possible to
make phone calls (indicated by a dial tone in the
receiver)
y = 1
if you pick up the receiver, the telephone keypad will
work as the keypad of the alarm system. It is impossible
to make phone calls in this mode (you will hear sounds
of the alarm keypad in the receiver)
y = 2
disabled - the telephone has no function
y = 3
emergency call – if you pick-up the phone, it will dial the
emergency number (see section 4.5)
Notes:
It is possible to switch from mode 0 (ordinary telephone line simulation) to mode 1 (alarm
system keypad) by pressing the “#” key (handset must be picked-up). The phone will return
to mode 0 after being hung-up.
In mode 3 (emergency call) it is possible (within 2 seconds after picking the handset up) to
switch to mode 0 (ordinary telephone line simulation) or mode 1 (alarm system keypad) by
pressing the “ *” or ” #“ key.
4.5. Emergency call number setting
If the attached telephone is programmed for emergency calls (see section 4.4), it will dial the
emergency number after the handset is picked up.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron JA-60GSM bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron JA-60GSM in de taal/talen: Engels als bijlage per email.

De handleiding is 0,28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Jablotron JA-60GSM

Jablotron JA-60GSM Installatiehandleiding - English - 11 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info