622294
9
Verklein
Vergroot
Pagina terug
1/55
Pagina verder
DVM68
25.02.2011
9
Continuity test
Press the / .button until the symbol appears on the display.
Connect the test leads to the circuit under test.
When the measured resistance is less than 50
Ω a continuous beep is produced and the
resistance value
is showed on the display. Should the measured resistance exceed the
selected range or in case of an open circuit, the display will show “OL
”.
Diode test
Press the / .button until the symbol appears on the display.
Connect the red test lead to the anode; connect the black test lead to the cathode of the
diode. The meter will display the approximate forward voltage drop. If the lead connection is
reversed, the meter will display “OL”.
Notes:
Never perform continuity or diode measurements on a live circuit and make sure all
capacitors are completely discharged.
Measuring diodes that are part of a circuit might produce faulty results.
disconnecting them from the circuit.
7.5 Capacitance measurements
Do not perform capacitance measurements on live circuits.
Connect the red test lead to the "mA Cx
" jack and the black lead to the "COM" jack.
Set the rotary switch to nF or µF.
Connect the test probes to the capacitor. Mind the
polarity when measuring polarized
capacitors.
The capacitance value is shown on the display.
Notes:
o It takes a few seconds before the meter stabilizes
. This is normal behavior.
o
The range control mode in capacitance measurement is manual ranging and only t
ranges (326nF, 32.6µF) are provided.
o
If Range Control Button is used in this measuring function, decimal points may be at
incorrect positions.
o
At the nF range, when the capacitor to be measured is not connected to test leads, the
LCD may not read zero, but a few counts. These counts
have to be substracted from
measuring results.
o
When the capacity is higher than the measuring range, the display shows ‘OL’.
o
Never perform capacitance measurements on a live circuit and make sure all capacitors
are completely depleted.
7.6 Frequency
measurements
Do not perform frequency measurements in circuits with voltages >
III of 1000V CAT II
Always be careful when working with voltages above 60Vdc or 30Vac rms. Keep your
fingers behind the probe barriers at
all times during measurement.
terminals when the meter is linked to a circuit which is being tested.
Connect the red test lead to the "VΩF
" jack and the black lead to the "
Set the rotary switch to Hz.
Connect the test probes to the circuit.
The frequency is shown on the display.
Notes:
o
The input voltage should be between 200mV and 10V rms AC. If the voltage is more than
10V rms, reading may be out of the accuracy range.
o When the frequency is higher than the measuring range, t
he display shows ‘OL’.
o
Use a shielded cable for measuring small signals in a noisy environment.
Rev. 01
©Velleman nv
Ω a continuous beep is produced and the
is showed on the display. Should the measured resistance exceed the
”.
Connect the red test lead to the anode; connect the black test lead to the cathode of the
diode. The meter will display the approximate forward voltage drop. If the lead connection is
Never perform continuity or diode measurements on a live circuit and make sure all
Measuring diodes that are part of a circuit might produce faulty results.
Consider
" jack and the black lead to the "COM" jack.
polarity when measuring polarized
. This is normal behavior.
The range control mode in capacitance measurement is manual ranging and only t
wo
If Range Control Button is used in this measuring function, decimal points may be at
At the nF range, when the capacitor to be measured is not connected to test leads, the
have to be substracted from
When the capacity is higher than the measuring range, the display shows ‘OL’.
Never perform capacitance measurements on a live circuit and make sure all capacitors
Do not perform frequency measurements in circuits with voltages >
600V CAT
Always be careful when working with voltages above 60Vdc or 30Vac rms. Keep your
all times during measurement.
Do not touch unused
terminals when the meter is linked to a circuit which is being tested.
" jack and the black lead to the "
COM" jack.
The input voltage should be between 200mV and 10V rms AC. If the voltage is more than
he display shows ‘OL’.
Use a shielded cable for measuring small signals in a noisy environment.
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Velleman DVM68 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Velleman DVM68 in de taal/talen: Nederlands, Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 0,9 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info