622294
7
Verklein
Vergroot
Pagina terug
1/55
Pagina verder
DVM68
25.02.2011
7
c. DATA HOLD button
When this button is pushed, the display will show the last reading and " D
appear until the button is pushed again.
Data holding will be cancelled automatically when the function switch is rotated.
d. AC/DC Current of / selecting button
Push this button to select AC or DC current measuring function when the function switch is set
at µA, mA, A positions.
Push this button to select or
measuring when the function switch is set at
position.
e. Input jacks
This meter has four input jacks that are protected against overload to the limits. During use,
connect the black test lead to the COM jack and the red
test lead as shown below
Function
Red Lead Connection
Input Limits
DCV / ACV
V /
/ F
1000V DC or 750V AC rms
kHz
V /
/ F
250V DC or AC rms
/ /
V /
/ F
250V DC or AC rms
µA / mA
mA / Cx
300mA DC or AC rms
nF / µF
mA / Cx
300mA fuse
A
A
10A DC or AC rms
µA/ mA and A ranges are protected by fuses.
7. Operation
Risk of electric shock during operation.
Be very careful when measuring live circuits.
Before measuring, always make sure the meter and/or test probes are not
verify the connections, selected function and range.
Never exceed the limit value for protection. This limit value is listed separately in the
specifications for each range of measurement.
Do not touch unused terminals when the meter is linked
to a circuit which is being tested.
Only use the meter in the indicated overvoltage/installation category. Never measure voltages
that might exceed the indicated category values.
Disconnect the test leads from the tested circuit before rotating the range
change functions.
When carrying out measurements on a TV set or switching power circuits, always remember
that high amplitude voltage pulses at the test points might damage the meter.
Always be careful when working with voltages above
60Vdc or 30Vac rms. Keep your fingers
behind the probe barriers at all times during measurement.
Do not measure current in circuits with voltages > 250V
Never perform resistance, diode, continuity or capacitance
measurements on live circuits.
Make sure all capacitors in the circuit are discharged.
7.1 Voltage measurements
Do not measure circuits wher
e voltages > 600V CAT III or >
occur.
Always be careful when working with voltages above 60Vdc or 30Vac rms. Keep your
fingers behind the
probe barriers at all times during measurement.
terminals when the meter is linked to a circuit which is being tested.
Connect the black test lead to the COM jack and the red test lead to the
Set the rotary selector to V for AC measurements or to V
for DC measurements.
Connect the test leads to the circuit under test.
The measured value appears on the display.
When desired, select a range manually with the RANGE button.
Rev. 01
©Velleman nv
When this button is pushed, the display will show the last reading and " D
-H " symbol will
Data holding will be cancelled automatically when the function switch is rotated.
Push this button to select AC or DC current measuring function when the function switch is set
measuring when the function switch is set at
/
This meter has four input jacks that are protected against overload to the limits. During use,
test lead as shown below
Input Limits
1000V DC or 750V AC rms
250V DC or AC rms
250V DC or AC rms
300mA DC or AC rms
300mA fuse
protected
10A DC or AC rms
µA/ mA and A ranges are protected by fuses.
Be very careful when measuring live circuits.
Before measuring, always make sure the meter and/or test probes are not
damaged and
Never exceed the limit value for protection. This limit value is listed separately in the
to a circuit which is being tested.
Only use the meter in the indicated overvoltage/installation category. Never measure voltages
Disconnect the test leads from the tested circuit before rotating the range
selector in order to
When carrying out measurements on a TV set or switching power circuits, always remember
that high amplitude voltage pulses at the test points might damage the meter.
60Vdc or 30Vac rms. Keep your fingers
measurements on live circuits.
e voltages > 600V CAT III or >
1000V CAT II may
Always be careful when working with voltages above 60Vdc or 30Vac rms. Keep your
probe barriers at all times during measurement.
Do not touch unused
terminals when the meter is linked to a circuit which is being tested.
Connect the black test lead to the COM jack and the red test lead to the
VΩF jack.
for DC measurements.
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Velleman DVM68 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Velleman DVM68 in de taal/talen: Nederlands, Duits, Engels, Frans, Spaans als bijlage per email.

De handleiding is 0,9 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info