670480
159
Verklein
Vergroot
Pagina terug
1/163
Pagina verder
Test the Path From Your Computer to a Remote Device
To test the path from your computer to a remote device:
1. From the Windows toolbar, click the Start button and select Run.
2. In the Windows Run window, type
ping -n 10 <IP address>
where <IP address> is the IP address of a remote device such as your ISP DNS server.
If the path is functioning correctly, messages display that are similar to those shown in Test the LAN
Path to Your Router on page 158.
3. If you do not receive replies, check the following:
Check to see that IP address of your router is listed as the default gateway for your computer. If
DHCP assigns the IP configuration of your computers, this information is not visible in your computer
Network Control Panel. Verify that the IP address of the router is listed as the default gateway.
Check to see that the network address of your computer (the portion of the IP address specified by
the subnet mask) is different from the network address of the remote device.
Check to see that your cable or DSL modem is connected and functioning.
If your ISP assigned a host name to your computer, enter that host name as the account name on
the Internet Setup page.
Your ISP might be rejecting the Ethernet MAC addresses of all but one of your computers.
Many broadband ISPs restrict access by allowing traffic only from the MAC address of your broadband
modem. Some ISPs additionally restrict access to the MAC address of a single computer connected to
that modem. If your ISP does this, configure your router to “clone” or “spoof the MAC address from the
authorized computer.
Troubleshoot 404 Error Message When Trying to Log In
to Plex Account
Plex Media Server helps you to manage your photos, videos, and audio files that are stored on an external
USB hard drive that is attached to your router.The router support Plex Media Server in both router mode
and AP mode. However, when your router is in AP mode, an error 404 error message might display when
you try to log in to your Plex account while using Windows 10.
To resolve a 404 error message after enabling Plex on your router
1. From your computer's hpme screen, right-click the network icon on the lower-right corner.
2. Select Open Network and Sharing Center > Change adapter settings.
3. Right-click the network adapter that connects to the router and select Properties.
4. In the Connection Properties window, clear the Internet Protocol Version 6 (TCP/IP) check box and
click the OK button.
Your settings are saved.
Troubleshooting
159
Nighthawk X10 AD7200 Smart WiFi Router
159

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Netgear R9000 - Nighthawk X10 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Netgear R9000 - Nighthawk X10 in de taal/talen: Engels als bijlage per email.

De handleiding is 4,42 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Netgear R9000 - Nighthawk X10

Netgear R9000 - Nighthawk X10 Aanvulling / aanpassing - Nederlands - 16 pagina's

Netgear R9000 - Nighthawk X10 Snelstart handleiding - Nederlands - 2 pagina's

Netgear R9000 - Nighthawk X10 Snelstart handleiding - Deutsch - 2 pagina's

Netgear R9000 - Nighthawk X10 Aanvulling / aanpassing - English - 16 pagina's

Netgear R9000 - Nighthawk X10 Snelstart handleiding - English - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info