628910
27
Verklein
Vergroot
Pagina terug
1/92
Pagina verder
Operating Instructions
Power Peak
®
D7 EQ-BID
Order No.
8129
12
13. STARTING A CHARGE / DISCHARGE PROCESS
Before the programmed process is started, the battery must be con-
nected to Output 1 or 2 with correct polarity (see chapter 5.2). Use
the appropriate charge lead from the comprehensive robbe range.
The process is actually started by pressing the "START / ENT." but-
ton: you will hear a confirmation beep. This means that the charger
is checking the battery connected to it; the screen informs you of
this.
If no battery is connected, you will see an on-screen warning of the
error, and hear a warning beep.
Note:Lithiumbatteriesmust alwaysbecharged withtheVoltage
Sensor lead connected.
Charge LiPo
Charge
Checking battery
Waiting. . .
14. SCREEN DISPLAYS DURING A PROCESS
14.1 SCREEN DISPLAYS DURING CHARGE / DISCHARGE
AND CYCLE PROCESSES
Once the process has started, the screen changes to the working
display, which shows all the important values relating to the cur-
rent process. The illustration below shows the working display for
a LiPo battery charge process. The working display is divided into
two screens.
Pressing the "START / ENT." button takes you to a display of the
voltage curve. If you are charging a Lithium battery, pressing the
"START / ENT." button a second time takes you to the Equalizer
display. Press the "START / ENT." button once more to return.
The displayed value for internal resistance is automatically calcu-
lated by the Power Peak
®
D7 EQ-BID.
Note:
It is possible to alter the current during a charge / discharge
process: navigate to the "CURRENT" function by pressing the
"START / ENT." button, then change the current using the "+" or
"-" buttons. The new value applies only to the current process, and
is not saved.
During a cycle process the working display also looks similar. The
screen displays "CYCLE" while the battery is being checked. The
illustration shows the upper part of the screen display during a
cycle, in this case while a battery is being charged.
When the charger is connected to the mains, i.e. the internal PSU
is in use as power supply, the "Input voltage" parameter shows a
valueof17.4V.
In addition to all the current process parameters, the screen dis-
plays the mode, the current phase and the cycle sequence. During
each phase the corresponding symbol flashes (D = Discharge, C
= Charge).
Cycle NiMH
Cycle : D>C
Time : 00.00.46
Capacity : 38mAh
Voltage : 5.77V
Current : 1.00 A
In.Volt : 11.78V
BATT. Res : 350 mO
Charge LiPo
Time : 00.00.46
Capacity : 19 mAh
Voltage : 11.54V
Current : 1.95 A
In.Volt : 11.78V
Batt.Res : 48mO
Int. temp. : 35°C
12. CONNECTING A BATTERY
Important!!! Before connecting a battery pack, check one
last time that all the set parameters are correct! If the settings are
incorrect, the battery may be damaged, explode, or catch fire. To
avoid short-circuits between the banana plugs, always connect the
charge leads to the battery charger first, and only then to the battery.
Take care to maintain correct polarity!
Reverse the sequence when disconnecting.
Connecting the equalizer:
The black wire of the voltage sensor lead attached to the Lithium
battery must be connected to the charger at the arrow marking. The
arrow indicates the negative terminal. Take care to maintain correct
polarity!
This example is only intended as a general guide; it shows how to
connect the voltage sensor lead to the equalizer.
Note:
It is essential to connect the battery voltage sensor lead to the
charger before charging or discharging a Lithium battery. This
is a safety requirement!
Do not connect the outputs in parallel, and never connect the
positive and negative terminals together. Neglecting this war-
ning will result in damage to the charger.
!
27

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Multiplex Power Peak D7 EQ-BID - 30 8129 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Multiplex Power Peak D7 EQ-BID - 30 8129 in de taal/talen: Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 9,26 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info