628910
25
Verklein
Vergroot
Pagina terug
1/92
Pagina verder
Operating Instructions
Power Peak
®
D7 EQ-BID
Order No.
8129
10
9. USER SETTINGS MENU
Pressing the "STOP / ESC" button switches to the main menu for
entering user data. These settings are global, and not specific to
any particular memory.
10. CYCLE DATA MENU
If no charge or discharge process is active, pressing the "STOP
/ ESC" button switches to the menu for viewing the cycle data.
Here you can view all the data relating to a charge or discharge
process.
The battery capacity is displayed both in the Charge (C:) line and
the Discharge (D:) line. The "C" line also displays the highest
voltage of the battery while the "D" line shows the lowest battery
voltage.
Press the "+" or "-" button to view all the data of a cycle (max. ten).
Note:
To erase the data, switch the charger off, or define a new battery.
(user setup)
Language : English
Rest Time : 2 min
Safety Cut : OFF
Safety Time : 1 min
Capa Ct : OFF
Capa value : 100 mAh
Key Beep : ON
(user setting)
Buzzer : ON
InputLow :10.5V
Int. Temp. : 39°C
Reset : Reset
Version :V1.00
Cycle data
No. Capacity Voltage
1C: 0mAh 11.358V
D: 0mAh 0.000V
2C: 0mAh 11.412V
D: 0mAh 0.000V
3C: 0mAh 0.000V
D: 0mAh 0.000V
11. MODE SELECT (CHARGE / DISCHARGE /
CYCLE)
Once all the charge / discharge parameters have been set, the
charge or discharge mode can be selected: hold the "START /
ENT." button pressed in for at least two seconds in the "Memory
name" menu. The screen display now changes, and you see a
menu for selecting the mode. The top line displays the essential
battery data. In the lower part of the upper screen you can set the
desired process.
To make a selection you must press the "+" or "-" button. To start
the process press the "START / ENT." button briefly. The following
charge processes are available for NiCd and NiMH batteries:
•Charge
•Automatic
Discharge
•Re-peak
•Cycle
The following charge processes are available for Lithium and Lead
batteries:
•Charge
•Discharge
Storage
•Fast-charge
•Balance
The example
alongside shows
the "CYCLE" pro-
cess; at this point
you can determine
the sequence of
the cycle, and the
number of cycles.
•C>D(charge/discharge)•D>C(discharge/charge)
(01) Memory name. .
NiMH 6-cell 2000 mAh
Cyclemode: D>C
Cycle : 1
Language
Menu language selection: English,
German, Italian and French
Pause
Pause setting between two cycles (1 - 60 min.).
This setting is only useful when charging NiCd /
NiMH batteries.
Time cut-off
If this function is active (ON), the process you
have started is interrupted when the set "time
limit" has elapsed, or when another cut-off
parameter is triggered, such as Delta-Peak,
final discharge voltage, etc. A corresponding
message is displayed.
Time limit
Time setting after which the process is stopped
automatically.Adjustmentrange:Off-720min.
Capacity cut-
off
If this function is active (ON), the process you
have started is interrupted when the set "capa-
city limit" is reached, or when another cut-off
parameter is triggered, such as Delta-Peak,
final discharge voltage, etc. A corresponding
message is displayed.
Capacity limit
Capacity setting after which a process is auto-
matically stopped. Adjustment range: 0.1 - 60
Ah
Button beep
Switch button beep on and off.
Buzzer
Switch melody on and off. The melody sounds
when a process is concluded, or to alert you to
an error.
Low voltage
At this point you can define the input level which
triggers a low-voltage alarm, e.g. in order to
protect a car battery used as power source
from becoming deep-discharged. Adjustment
range:10.3V-11.0V,variablein0.1Vincre-
ments.
Int. temp
Displays the internal temperature of the charger.
Reset
Selecting this point erases all the previously set
parameters, and restores them to the factory
default values. This is achieved by holding the
"START / ENT." button pressed in for at least
two seconds.
Version
Display of charger firmware version.
25

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Multiplex Power Peak D7 EQ-BID - 30 8129 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Multiplex Power Peak D7 EQ-BID - 30 8129 in de taal/talen: Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 9,26 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info