628910
29
Verklein
Vergroot
Pagina terug
1/92
Pagina verder
Operating Instructions
Power Peak
®
D7 EQ-BID
Order No.
8129
14
16.2 READING OUT THE DATA ON A BID CHIP
If you wish to read out the saved data, you must first press the
"STOP / ESC" button. This display now shows the maximum
charged-in and discharged capacity of all the charge / discharge
processes involving this battery.
Note:
The data cannot be displayed if any process (charging, dischar-
ging, etc.) is currently active.
The illustration shows a typical screen display, which gives you a
means of estimating the values for your battery, and accurately
assessing the overall state of the pack . No additional equipment,
such as a PC with the appropriate software, is required.
An analysis of the example display shows the following:
•Todatethebatteryhasbeenchargedtwicewiththecharger,
terminating with the "END" message.
•Thehighestcharged-incapacitywas1100mAh.Atthe
moment a capacity of 1000 mAh has been charged in.
•Thehighestdischargedcapacitywas600mAh.Atthemoment
a capacity of 500 mAh has been discharged.
BID Info
LiPo11.1V4000mAh
Last ChgCapa : 1000 mAh
Max ChgCapa : 1100 mAh
Num ChgCycles: 2
Last dChgCaps: 500 mAh
Max dChgCaps: 600 mAh
19. ERROR MESSAGES
The Power Peak
®
D7 EQ-BID is equipped with special safety fea-
tures to ensure safe and reliable charging and discharging operati-
ons. As soon as a fault occurs, a corresponding message appears
on the screen, and the piezo buzzer emits a warning tone. After
eliminating the cause, you can erase the following error messages
by pressing the "STOP / ESC" button.
[ Error ]
DC input too low
* Please check the
Input voltage!
[ Error ]
Interruption
* The battery
is disconnected.
* Please connect the battery
and start.
[ Error ]
Reverse polarity
* The battery is connected to
the output with reversed
polarity!
[ Error ]
Balance lead error
* Connect the
balance lead.
[ Error ]
DC input too high
* Please check the
Input voltage!
[ Error ]
Capacity limit
* The set capacity
limit has been reached.
[ Error ]
Cell count incorrect
* Incorrect number of cells set
[ Error ]
No battery
* No battery is
connected to the output.
[ Error ]
Cell error
*Voltageofonebatterycellis
too low.
[ Error ]
Connection error
* The battery was disconnected
during an active process.
* Possible short-circuit
at the output.
18. USB PC SOCKET
The Power Peak
®
D7 EQ-BID is fitted with two mini-USB sockets
at the front. A USB lead can be connected to either of these sok-
kets for connection to a PC. The appropriate lead can be obtained
from any electronics shop. Software updates can be loaded using
this lead.
USB charge socket
Thechargerisfittedwitha5V/1AUSBchargesocketonthe
front. This can be used for charging smart-phones and digital
cameras.
16.1 STARTING CHARGE / DISCHARGE PROCESSES WITH
BID CHIP / KEY
When you have edited and saved the BID data, the "BID EDIT"
screen display appears. Processes are initiated from this display.
This is accomplished by holding the "START / ENT." button
pressed in for at least two seconds. The various modes (CHARGE,
DISCHARGE, STORAGE, FAST-CHARGE, BALANCE, etc.) are
then displayed.
The procedure is identical to that required for starting a process for
one of the twenty memories ("Memory name" menu). The same
set-up facilities and parameters are available.
After highlighting the desired process using the "+" or "-" but-
tons, hold the "START / ENT." button pressed in for at least two
seconds to start.
saved to the BID chip or key: navigate to the "Store" line, and press
the "START / ENT." button to save the data.
If the BID chip or key has already been operated with another char-
ger, the data are naturally adopted. However, if the set parameters
are not compatible with the D7 charger (charge / discharge current,
cell count, capacity or "Special" battery with the Power Peak E1), an
error message appears, and you have to re-enter the data.
17. CHARGE OUTPUT 2 / OUT2
The Power Peak
®
D7 EQ-BID charger is fitted with a second charge
output, which has the same specification as Output 1. Both charge
outputs can be operated independently of each other.
Note:
Do not wire the outputs together in parallel or in series!
29

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Multiplex Power Peak D7 EQ-BID - 30 8129 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Multiplex Power Peak D7 EQ-BID - 30 8129 in de taal/talen: Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 9,26 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info