554895
2
Verklein
Vergroot
Pagina terug
1/7
Pagina verder
Digital communicator JA-65X 2/7 MFM53102
2.3 Voice message(s) recording
sequence: 8x
You can record two different voice messages (10 sec. each).
Depending on the setting in section 2.4, a particular message
will be sent under different situations. Recording of the
messages:
a) enter 85 on the keypad
b) press and hold push button on the X module
c) speak towards the module (max. 10 s)
d) release the button, message will play back
This results in the recording of message number 1. To record
message 2 enter 86 in step a)
If you prefer sending only one, but longer, message (20 sec.),
record message by entering 84 in step a). By programming as
described in section 2.4 you can specify which alarms will trigger
the sending of a message.
Notes:
Make the messages brief and clear. The dialer repeats the message to
each called number for 40 seconds.
The voice messages are stored in non-volatile memory and can be
changed when ever you want to by repeating the above steps.
The existing messages can be played by momentarily pressing the push
button on the X module (or by entering F9 while in stand by mode).
2.4 Triggering of voice and SMS messages
sending sequences: 9 y x
With sequences 91x to 95x you can select which alarms will
trigger the telephone dialer to call and what will be sent.
Enter: 9 y x
where:
y Alarm x reaction
1 Panic – silent 0 no reaction
2 Intruder 1 voice1 and SMS
3 Fire 2 voice 2 only
4 Tampering 3 SMS only
5 Technical trouble
Notes:
Final texts of alarm SMS are generated by the SMS server
(providers computer) – based on the digital code sent by
the alarm system (check with provider for more details)
If only one long voice message was recorded by using code
84 as described in section 2.3, then this message will be
sent when x=1 or x=2
Voice messages are sent step by step to all telephone
numbers programmed as described in section2.1
SMS message is sent to a mobile phone number
programmed as described in section 2.2
Example: if the dialer should send an SMS and voice message
1 when intruder or panic alarm is triggered, voice message 2 in
the case of fire and only an SMS in the case of technical alarm,
enter: 911 921 932 943
Factory default setting: all alarms will trigger sending of voice
message 1 and SMS (911, 921, 931, 941, 951).
2.5 Dialing method
sequence: 9 0 x
Enter:
9 0 1 for tone dialing
9 0 0 for pulse dialing (this option is blocked for
some countries)
Note: this dialing method setting is also valid for Central
monitoring station communications.
Factory default: tone dialing
2.6 Telephone line checking
sequence: 9 9 x
If this function is enabled, the dialer will check regularly if the
telephone line is ready to make a phone call. If the line is not
ready for more than 15 minutes, the keypad will indicate a
telephone line failure (failure L). A non-working telephone line or
a phone conversation or Internet connection longer than 15
minutes can cause a fault.
options:
9 9 1 checking enabled
9 9 0 checking disabled
Note: this setting is also valid when the dialer is used for
Monitoring station communications as well as remote PC access
Factory default setting: checking disabled
2.7 Telephone dialer testing
sequence: 8 9
After entering code 89 the dialer will call all programmed numbers
and will play voice message 2. It will also send a SMS message if
programmed. The telephone line signals will be audible from the
control panel’s built in speaker during the test (if the dialer is
triggered by an alarm in normal operation, it will call silently).
If you prefer testing with voice message 1 enter code 88.
Testing can be terminated with the N key.
3 To enable a remote computer to dial in
When the user or installer wants to dial in to the installation
from their computer or a remote JA-60E keypad via a JA-60U
modem (see section 6), the following parameters should be
programmed.
The most convenient programming is via a connected PC
using the Comlink software. Programming can also be
performed manually:
Enter the programming mode when disarmed (F 0
Service Code, factory default 6060), indicated by a ”P“
Any unfinished programming sequence can be
terminated by the N key.
To exit the programming, press the N key (“P“ will
turn off).
Dialing in parameters
Function sequence options factory d.
Incoming call reaction 0 5 x
0=never
1= second call
2-6 = after ring
No. 2 - No.6
disabled
Remote access code
(8 digits)
0 7
xxxxxxxx
any 8 digits
code
00000000
3.1 Reaction to an incoming call
sequence: 05
This sequence sets how the communicator will react to incoming
calls on the telephone line. This setting is important for remote
access. Enter:
0 5 x
where: x = 0 - never answer
1 - answer after second call = after 1 or 2 rings are
detected, there must be a pause of 10 - 45
seconds. The dialer will then answer on the very
first ring of the second call. This setting can be
used to bypass an answering or facsimile
machine connected to the same line. This
“Second Call” feature is supported by the
Comlink software and also by the JA-60E
keypad.
2 to 6 - answer after 2
nd
to 6
th
ring
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron JA-65X bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron JA-65X in de taal/talen: Engels als bijlage per email.

De handleiding is 0,17 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info