554884
6
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
JA-60GSM dialer module 6 / 11 MFJ51215
4.2.2 Editing of remote control SMS commands
If you change any of the text strings from 703 to 711, the dialer will
recognize the new text string as the valid remote control command.
E.g., if you change text “MO” (number 705) to “Tell me my alarm
status please” it will be possible to read the control panel status by
sending the new string as the SMS command. This function helps
customers keep the commands secret and protect the dialer against
unauthorized operation.
4.3 Assignment of audible warnings to be reported
Table 4.3.1 shows the complete list of all possible events in the alarm
system. It also shows which events are assigned to which telephone
numbers to be reported audibly. You can make your own setting by:
82 uu t y
where
uu is an event index from 01 to 31
t is a telephone number memory location from 1 to 8
y 0 = reporting disabled, 1 = reporting enabled
4.3.1 Table – audible warning assignments to telephone numbers
The x marks in the table show which events are assigned to which telephone numbers to be reported audibly. If you modify these, we recommend you
mark your setting in the table. If there is an alarm, a siren sound will be played, for other events a melody sound will be played.
Telephone numbers
Event index uu Event
1 2 3 4 5 6 7 8
01 Intruder alarm – instant zone x x x x x
02 Intruder alarm – delayed zone x x x x x
03 Fire alarm x x x x x
04 Panic alarm x x x x x
05 Wrong access code alarm x x x x x
06 Alarm after power on x x x x x
07 Tamper alarm x x x x x
08 Tamper OK
09 Alarm end
10 Alarm canceled by a user
11 Arming
12 Disarming
13 Partial arming (Home)
14 No code arming
15 External communication failure
16 External communication recovery
17 Failure
18 Failure recovery
19 AC failure longer than 30 minutes
20 AC failure
21 AC recovery
22 Battery failure
23 Battery recovery
24 Enter programming mode
25 Exit programming mode
26 Remote access
27 Remote access – end
28 RF jamming
29 Internal communication failure
30 Internal communication recovery
31 Periodic test
Example: if you enter 820381 and a Fire alarm is triggered (event index 03) the dialer will call the 8
th
telephone number and it will play audible warning if
the call is answered.
4.4 Temporarily disabling SMS and audible reports
If you need to disable all SMS and audible reports temporarily to all
telephone numbers, use the following sequence:
800 all reports disabled the communicator will send
neither the alarm SMS nor acoustic warnings
801 all reports enabled the communicator will send the
audible reports and SMS messages according to the settings
in chapter 4.1.1. and 4.3.1.
802 the communicator will send the preset reports except the
events of "arming" and "disarming" by Master code, user codes 1 to
4 and controllers 1 to 4
Default setting: all reports enabled (801).
5 General settings
Enter programming mode if you are going to use any of the following
sequences.
5.1 Using a SIM card with a PIN code
It is recommended to use a SIM card with the PIN code protection
disabled (this can be done with a mobile phone, see section 1). If you
insist on using a PIN code, enter it after the GSM dialer has been
powered up using:
70 xxxx F0
where:
xxxx is the PIN code (4 digits)
Example: if the PIN code is 1234 enter 701234F0
Default setting: 70F0 the PIN code protection is off
Note:
If the dialer does not connect to the GSM network after
powering up (LED starts flashing), there is a probability that a
wrong PIN code was set. In this situation:
o enter 70F0 on the control panel keypad when in programming
mode (PIN code erasing in the dialer)
o disconnect the control panel’s power supply (AC and battery)
o remove the SIM card, insert it into a mobile phone and check
the PIN code. Check also that it is possible to connect to the
desired GSM network at the location of the dialer’s GSM
antenna.
o if you are sure the PIN code is right and the location is covered
by a GSM signal, insert the SIM card back in to the dialer, switch
the power supply on, enter the PIN code (70 PIN F0) and wait
until the communicator connects to the GSM network (LED will
turn off).
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron JA-60GSM bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron JA-60GSM in de taal/talen: Engels als bijlage per email.

De handleiding is 0,19 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Jablotron JA-60GSM

Jablotron JA-60GSM Gebruiksaanwijzing - English - 6 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info