554883
4
Verklein
Vergroot
Pagina terug
1/5
Pagina verder
GSM communicator GD-06 Allegro – complete manual 4/5 MHG 51203
51 On
52 Off
60 P6
61 On
62 Off
70 Relay
71 On
72 Off
80
GD-06 reports description of device -
for example „COMPRESSOR
ROOM REPORTS“
81 Event
82 Status
83 SMS syntax error
84
Setting has been
done
85
Command has been
done
86
GSM network
recovery
87
Power supply
recovery
88 Credit
89 Credit request failure
90 GSM level signal
tab. 5
4. Setting of special functions
4.1. HF-03 hands-free set
Connected HF-03 hands-free set cannot be used for making direct
phone calls from Allegro. But by incoming SMS message “USER
(MASTER) CALL”, DTMF code or activation of input can be activated
“monitoring mode”. This can be especially used for listening to the area
in case of alarm.
MASTER HF M,S RING T,V,E DTMF XXXX
Where:
M Volume of microphone (0 to 9)
S Volume of speaker (0 to 9)
T Setting of ringing before phone call will be received (0-60sec.)
V Volume of ringing (0-9)
E Melody of ringing (0=without melody, 1-10 melodies)
XXXX Setting of DTMF code (up to 10 figures) for switching the
incoming phone call to the monitoring mode. It is important to
enter DTMF codes without any repetition in their sequencing.
For example If there is code 123, it is not possible to use
another code 12345 - after receiving the initial 123 it is
recognized as the correct code, the command will be
performed and 4 will be considered as the beginning of a new
code.
If there is no DTMF code used (neither for HF, nor for operating of
terminals P1-P6 or RELAY), the incoming phone call is switched to
monitoring mode immediately (except the calls made from phone
numbers preset for controlling the Allegro by dialing-in 5.2.).
MASTER HF 3, 4 RING 20, 5, 1
- Allegro receives a phone call in 20 seconds, it will ring using melody
number 1 at volume 5. Volume of the microphone will be at level 3
and the volume of the speaker will be at level 4.
4.2. Credit balance
MASTER (USER) CREDIT parameters
The Allegro can send information about the credit balance of a
prepaid SIM card. An SMS sent from any of the stored numbers
containing the word CREDIT followed by the correct instruction
(different for every provider) will result in the sending of the information
about the credit. Please ask your mobile phone provider for more
information.
MASTER (USER) CREDIT uuuuu
Where uuuuu is a string, which depends on the GSM provider. Ask
your provider for more details
If you want to check the credit regularly use the following sequence.
CREDIT uuu..u xx yyy zz
Where: uuu…u is the instruction given by the provider for receiving
information about the amount of credit
xx is the time period (in days) for checking.
yyy is minimum level of credit
zz is a position of the credit in the information SMS sent
by the provider
- If the level of the credit is lower than set value (yyy) the information
will be sent to the telephone numbers that have the ERROR setting
preset (see 4.4.).
4.3. Sustains calls
MASTER TELP
If a prepaid card is used, the dialer can automatically perform a sustain
call when there was no call within a 3 month period. It will dial the
programmed number and after 10 second call duration the dialer will
hang up. The number, which should be called, can be entered by:
MASTER TELP 14112
- phone call to number 14112 is made every three months
4.4. Error reports
ERROR TX
Command is used for programming the numbers to which error
messages are sent – after failure of power supply, failure of GSM
network and low credit of pre-paid card. Messages will be sent after
restoration of communication. Failure of GSM must be longer than 15
minutes. Command: MASTER ERROR DEL will cancel sending of the
error messages.
MASTER ERROR T1 T7
- to send information about errors to phone numbers TEL1 and TEL7
4.5. GPRS setting
MASTER GPRS APN, NAME, PASSWORD, CONFIRM
If it is required to get access to www.gsmlink.cz or to send data in
GPRS format it is necessary to set proper parameters first. Parameters
can be different for every GSM provider. For details ask your GSM
provider.
APN Access point name (e.g. Eurotel in The Czech Republic
has APN “internet”)
NAME user name (it may not be required by operator)
PASSWORD user password (it may not be required by operator)
CONFIRM 1 confirm; 0 do not confirm (Any option can be set -
command confirm is not used at the present time. it is prepared for
future appliances)
Note: Parameters in the setting SMS must be separated by commas
and blank space. Any parameter which is not required can be replaced
by a blank space. The programming sequence can be finished by
setting the last required parameter.
Examples of setting SMS:
MASTER GPRS internet
- To set the name of the access point APN to “internet”
MASTER GPRS internet, , ,1
- To set APN to “internet”, access name and password are blank,
confirmation is activated
MASTER GPRS DEL
- To delete all parameters. Connection via GPRS will not be possible.
4.6 RESET
To reset the Allegro to the factory default settings:
RESET EN
- set parameters to factory default setting (tab. 1), all texts will be in
English (tab.5 and 6)
RESET PAR
- set parameters to factory default setting (tab. 1), texts will not be
changed
RESET GSM
- to disconnect from the GSM network for a short moment. This function is
useful when it is necessary to switch the mobile device off and on (e.g.
when the SIM card has been unblocked by the mobile operator).
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron GD-06 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron GD-06 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,08 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Jablotron GD-06

Jablotron GD-06 Gebruiksaanwijzing - English - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info