554883
2
Verklein
Vergroot
Pagina terug
1/5
Pagina verder
GSM communicator GD-06 Allegro – complete manual 2/5 MHG 51203
From a GSM phone, you can send an SMS instruction to switch on
or off the P5 and P6 outputs (example: “ON P5”, “OFF P6”).
You can also switch the relay on or off by making a phone call to
the GD-06 from a phone registered to TEL1 or TEL2 memory
positions. The GD-06 ALLEGRO doesn’t answer this call, so you
are not charged any telecommunication fee for this remote control.
Notes:
1. You can remotely control the GD-06 from any phone: not only from
the ones stored in the memory TEL1-TEL8. You must just add the
master (default MASTER) or a user (default USER) access code in
front of the instruction.
Example: “MASTER ON P5”
2. The SMS instruction texts are case insensitive. This means that
the instruction “ON P5” is equal to “on p5”.
2.4. Access codes MASTER - USER
Parameter settings:
You can set the communicator without using the MASTER access code
if the jumper MASTER is in the NO MASTER position. If it is in the
MASTER position, then a valid MASTER code must be used. (see
figure 1)
For quick installation it is recommended to set the jumper to the NO
MASTER position. However, for security reasons, during normal
operation the jumper should stay in the MASTER position
3. Advanced setting
General rules for following SMS setting sequences:
1. Jumper is in the MASTER position (it means that the MASTER
code is required)
2. Setting sequences are not case sensitive.
3. Key words must be separated with a space
4. In the examples are used the SMS text, which will be set after the
RESET EN (factory default setting).
5. There can be multiple commands in one SMS, which must be
separated with comma and a blank space.
3.1. Setting of inputs INP
Terminals P1 to P6 can be programmed as inputs. A single SMS
must be always used to program the input, desired parameters as
well as the corresponding phone numbers. If it is necessary to
reprogram the input (for example to add another phone number), all
previously set parameters must be in a new programming SMS sent
again.
MASTER PX INP TYz TYz
Where:
X is the number of terminal P1 – P6
Y is the position of the phone number to which the SMS will be
sent
Z + , – or nothing, depending on the required function
Setting of inputs
Parameter Description
P1, P2, … P6
The name of the terminal which will be programmed as
input via SMS*
INP Parameter for programming a terminal as an input
T1, T2, ….T8 Phone numbers (TEL1 to TEL8)
+ Activation (connecting to GND) will cause sending SMS
-
Deactivation (disconnecting from GND) will cause
sending SMS
Without + or – parameters the SMS will be sent in case
of any change of input (connecting/disconnecting
to/from GND)
DEL
All previous settings will be erased. No confirmation
SMS will be sent.
* Description of terminal can be changed, but P1, P2 etc, must be
always used in the setting sequences.
tab. 2
Examples of setting SMS:
MASTER P1 INP T2 T3
- Terminal P1 will be set as an input, message about any change of
the input will be sent to TEL2 and TEL3
MASTER P3 INP T4+ T7 T8-
- Terminal P3 will be set as an input, TEL4 will be notified on
activation, TEL8 on deactivation and TEL7 will be notified on all
changes of the input.
MASTER P6 DEL
- All previous settings for terminal P6 will be deleted. The terminal will
be programmed as an input, information about the change will not be
sent to any phone number
Note:
The input signals shorter than 200ms (factory default) will be ignored.
The input filter can be adjusted from 50ms up to 20 seconds.
There are analog inputs, which have adjustable level of their activation
and deactivation (hysteresis). They can also be used for measuring of
analog values (voltage).
Both settings can only be changed via GSMLINK web page. Factory
default setting will be automatically restored after reset.
3.2. Setting of outputs OUT
Relay (NO,C,NC) is always output, terminals P1 to P6 can be
programmed as outputs. A single SMS must be always used to
program the output, desired parameters as well as the
corresponding phone numbers. If it is necessary to reprogram the
output (for example to add another phone number), all previously set
parameters must be in the programming SMS sent again.
MASTER PX OUT parameters or for output relay:
MASTER RELAY parameters
Where:
X is number of terminal P1 – P6
RELAY is the relay output
Parameters parameters according to table 3
Setting of outputs
Parameter Description
P1, P2, … P6
RELAY
The name of the terminal, which will be programmed
as output via SMS*
OUT Parameter for programming a terminal as an output
T1, T2, ….T8
ALL
Phone numbers TEL1 to TEL8, from which will be an
output terminal switched on or off when dialling in
- the output will be controlled by a phone call from all
saved phone numbers
INT
s,m,h
Activation of the output for the preset period of time –
after dialling-in or DTMF code
- duration is programmed by number (selectable from
1 to 99) and unit s-second, m-minutes, h-hours
NEG
Negation of the output status – after dialling-in or
DTMF code
DTMF
To set the controlling DTMF code. The output will be
controlled when the correct DTMF code from the
telephone keyboard of the phone, which is calling to
the Allegro, is received. It is important to enter DTMF
codes without any repetition in their sequencing. For
example If there is code 123, it is not possible to use
another code 12345 - after receiving the initial 123 it
is recognized as the correct code, the command will
be performed and 4 will be considered as the
beginning of a new code.
Figures 0, 1, … 9,*,# can be used; (up to 10 digits)
TEMP
To set a temperature switch – if the temperature drops
below the preset level (set in °C) the output will be
switched on. Hysteresis is 0,5 °C
(hysteresis is adjustable only via www.gsmlink.cz
)
DEL
All previous settings will be erased. No confirmation
SMS will be sent.
* Description of position can be changed, but P1, P2 etc, must always
be used when programming setting sequences.
tab. 3
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron GD-06 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron GD-06 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,08 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Jablotron GD-06

Jablotron GD-06 Gebruiksaanwijzing - English - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info