674740
78
Verklein
Vergroot
Pagina terug
1/154
Pagina verder
Page 76
FT-991 OperaTing Manual
The powerful CW operating capabilities of the
FT-991
permit operation using an electronic keyer paddle, a “straight
key”, or a computer-based keying device.
Setup For StrAight key
(
And StrAight key eMulAtion
)
operAtion
Before starting, connect your key line(s) to the front panel
KEY
jack. Be sure
[
BK-IN
]
displayed by pressing the
F(M-
LIST)
button is turned off for now.
1. Press the
MODE
button, then touch
[
CW-LSB
]
or
[
CW-USB
]
on the TFT LCD display. The “
C-L
or “
C-U
icon will appear in the display. The CW
monitor is activated.
MULTI Knob
MODE Button
F(M-LIST) Button
2. Rotate the Main Tuning Dial knob to select the de-
sired operating frequency.
3. Press the
F(M-LIST)
button, then touch
[
BK-IN
]
on the LCD to engage automatic activation of the
transmitter when you close the CW key. The Break-
in will be set to “
ON
”.
Advice:
When you close the CW key, the transmitter will
automatically be activated, and the CW carrier
will be transmitted. When you release the key,
transmission will cease, and after a brief delay,
receive will be restored. The delay time is user-
programmable per the discussion on page 83.
As shipped from the factory, the
FT-991
TX/RX
system for CW is congured for “Semi-break-in”
operation. However, using Menu item
056 CW
BK-IN TYPE
”, you may change this setup for full
break-in (QSK) operation, whereby the switch-
ing is quick enough to hear incoming signals in
the spaces between the dots and dashes of your
transmission. This may prove very useful during
contest and trafc handling operations.
4. CW operation using the CW key may now proceed.
Advice:
The CW sidetone audio level may be adjusted by
setting “MONITOR” (see page 72).
You may practice sending CW listening to the sidet-
one only, without having the signal transmitted out
over the air, if you press the front panel
F(M-LIST)
button to reveal the functions list on the TFT LCD
display, and then touch the [
BK-IN
] button to set
break-in to Off.
If you reduce transmit power via the [
RF PWR
]
function that may be displayed by pressing the
F(M-
LIST)
button, the ALC meter reading will increase;
this is normal and does not indicate any problem
whatsoever (because increased ALC voltage is being
used to lower the power).
To enable the keying operation in LSB/USB mode
and send the CW signal without switching to CW
mode, change Menu item “
055 CW AUTO MODE
”.
The same frequency may be displayed when switch-
ing between SSB mode and CW mode by setting
Menu item “
059 CW FREQ DISPLAY
”.
By connecting the
FT-991
to a computer, CW can
be operated using free or commercially available
software and setting Menu item “
060 PC KEYING
”.
cw MoDe operation
78

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu FT-991 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu FT-991 in de taal/talen: Engels als bijlage per email.

De handleiding is 30,58 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info