478500
54
Verklein
Vergroot
Pagina terug
1/76
Pagina verder
Page 52 FT-897D OPERATING MANUAL
BEACON FEATURE
The FT-897Ds unique “Beacon” feature allow you to set up the transceiver to send a repetitive message. For example, on a
DX-pedition, the FT-897D beacon might be activated on a 50 MHz frequency, to alert DXers as to possible band openings.
MISCELLANEOUS SETTINGS
Beacon Transmission (On the Air)
1. Press and hold in the
[
F
]
key for one second to enter the
Menu mode.
2. Rotate the MEM/VFO CH knob to select Menu Mode
No-012
[
BEACON TIME
]
.
3. Rotate the DIAL to select the interval time (between mes-
sage and message) (1 ~ 255 seconds).
4. Press and hold in the
[
F
]
key for one second to exit to
normal operation.
5. Press the
[
F
]
key momentarily, then rotate the MEM/
VFO CH knob, as needed, until Multi Function Row
“o”
[
PLY1, PLY2, PLY3
]
appears on the display.
6. Press the
[
A
](
PLY1
)
key to activate the Beacon Feature.
NOTE: When using the “beacon” feature, please disable the
“VOX” feature.
If you press
[
B
](
PLY2
)
or
[
C
](
PLY3
)
, the mes-
sage will be transmitted, after which the trans-
mission will halt. Operationally, these two keys
function the same as a traditional CW message keyer.
7. To disable the transmission from the Beacon, just repeat
the above procedure, rotating the DIAL to select “OFF
in step 3 above.
You may adjust the CW speed using Menu Mode
No-030 [CW SPEED].
You may also send the Beacon Text manually. If this is done,
all three “Beacon” messages may be used as a traditional
CW message keyer. To do this:
1. Press and hold in the
[
F
]
key for one second to enter the
Menu mode.
2. Rotate the MEM/VFO CH knob to select Menu Mode
No-012
[
BEACON TIME
]
.
3. Rotate the DIAL to select “OFF.”
4. Press and hold in the
[
F
]
key for one second to exit to
normal operation.
5. Press the
[
F
]
key momentarily, then rotate the MEM/
VFO CH knob, as needed, until Multi Function Row
“o”[PLY1, PLY2, PLY3] appears on the display.
6. Press the
[
A
](
PLY1
)
key momentarily to send the “BEA-
CON TEXT 1” message.
Alternatively, pressing the
[
B
](
PLY2
)
or
[
C
](
PLY3
)
key
will initiate the message at those respective break points.
Beacon Text Storage
1. Press and hold in the
[
F
]
key for one second to enter the
Menu mode.
2. Rotate the MEM/VFO CH knob to select Menu Mode
No-011
[
BEACON TEXT 1
]
.
3. Press the MEM/VFO CH knob to enable storage of the
Beacon Text (the first character location will be underlined).
4. Rotate the DIAL to select the first character (number or
letter) in the Beacon Text you wish to store, then rotate
the MEM/VFO CH knob one click clockwise to move
to the next character.
5. Repeat step 4 as many times as necessary to complete
the Beacon Text.
If the Beacon Text is less than 40 characters long,
add the “ ” mark after the last character to terminate
the text, then press the MEM/VFO CH knob.
If the Beacon Text is more than 40 characters long,
but less than 79, set the last (40th) character to be
,” press the MEM/VFO CH knob, then rotate the
to select “BEACON TEXT 2.” Now repeat step 4.
If the Beacon Text is more than 79 characters long,
up to 118 characters may be stored. In this case, set
the final character slot in “BEACON TEXT 2” to be
,” press the MEM/VFO CH knob, then rotate the
to select “BEACON TEXT 3.” Now repeat step 4.
Do not forget to install the “ ” mark after the last
character, to terminate the text.
6. Press and hold in the
[
F
]
key for one second until you
hear a double beep; the second beep confirms that the
Beacon text was successfully stored.
54

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu FT-897D bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu FT-897D in de taal/talen: Engels als bijlage per email.

De handleiding is 3,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info