478500
56
Verklein
Vergroot
Pagina terug
1/76
Pagina verder
Page 54 FT-897D OPERATING MANUAL
Available Values Default
ON/OFF OFF
ON/OFF 1
ON/OFF 1
ENABLE/DISABLE DISABLE
0 ~ 100 50
2.5/5/9/10/12.5/25kHz 1
OFF/1h ~ 6h OFF
OFF/RANGE/ALL RANGE
ON/OFF OFF
YAESU
––
OFF/1 sec ~ 255 sec OFF
440/880/1760 Hz 880 Hz
0 ~ 100 50
–300 ~ +300 Hz 0 Hz
–300 ~ +300 Hz 0 Hz
–300 ~ +300 Hz 0 Hz
–300 ~ +300 Hz 0 Hz
4800bps/9600bps/38400bps 4800bps
CAT/LINEAR/TUNER CAT
CLAR, M/V, MAIN CLAR
ON/OFF OFF
USB/LSB/AUTO USB
FULL/30 ~ 3000 msec 250 msec
NORMAL/REVERSE NORMAL
ELEKEY/MICKEY ELEKEY
400 ~ 800 Hz 700 Hz
10/15/20/25/30 ms 10 ms
0 ~ 100 50
4 ~ 60 wpm (1wpm/step)/ 12 wpm
20 ~ 300 cpm (5cpm/step) (60 cpm)
N, A, AN N
1:2.5 ~ 1:4.5 1:3.0
104 Standard DCS codes 023
Tn-Rn/Tn-Riv/Tiv-Rn/Tiv-Riv Tn-Rn
FINE/COARSE FINE
–3000 ~ +3000 Hz 0 Hz
0 ~ 100 50
RTTY-L/RTTY-U/PSK31-L/ RTTY-L
PSK31-U/USER-L/USER-U
–3000 ~ +3000 Hz 0 Hz
Function
Enables/Disables the extended Menu Mode.
Activates/deactivates the Automatic Repeater Shift feature when
operating on the 144 MHz band.
Activates/deactivates the Automatic Repeater Shift feature when
operating on the 430 MHz band.
Enabling/disabling the DIAL knob on the AM and FM modes.
Adjusts the microphone gain level for the AM mode.
Selects the tuning steps for the MEM/VFO CH knob on the AM mode.
Selects the Auto Power Off time (time before power goes off).
Selects the ARTS beep mode.
Enables/disables the CW identifier during ARTS operation.
Stores your callsign into the CW identifier.
Stores the message for the Beacon.
Selects the interval time (between message and message).
Selects the beep frequency.
Selects the beep volume level.
Sets the Rx Carrier Point for LSB.
Sets the Tx Carrier Point for LSB
Sets the Rx Carrier Point for USB
Sets the Tx Carrier Point for USB
Sets the transceiver’s circuitry for the CAT baud rate to be used.
Selects the device which is connected to the CAT/LINEAR jack
on the rear panel.
Defines the “control” knob to be used for setting of the clarifier
offset frequency.
Selects whether the KEY jack shall be “Enabled” or “Disabled”
while using the SSB/FM modes.
Sets the CW carrier oscillator injection side on the CW mode.
Sets the receiver recovery time during pseudo-VOX CW semi-
break-in operation.
Sets the keyer paddle’s wiring configuration.
Enables/disables CW keying by the microphone’s [UP]/[DWN]
keys.
Setting of the pitch of the CW sidetone, BFO offset, and CW filter
center frequencies.
Selects the time delay between when the PTT is keyed and the car-
rier is transmitted during QSK operation when using the internal keyer.
Setting of the CW sidetone volume level.
Sets the sending speed for the built-in Electronic keyer.
Sends random Morse Code five-character groups via the sidetone.
Sets the Dot:Dash ratio for the built-in electronic keyer.
Setting of the DCS code.
Selects “Normal” or “Inverted” DCS coding.
Setting of the DIAL knob’s tuning speed.
Defines the displayed frequency offset during DIG (USER-L or
USER-U) mode operation.
Adjusts the audio input level from terminal equipment during DIG
(Digital) mode operation.
Selects the mode and sideband in the DIG (Digital) mode.
Defines the carrier frequency offset during DIG (USER-L or USER-
U) mode operation.
No Menu Item
001 EXT MENU
002 144MHz ARS
003 430MHz ARS
004 AM&FM DIAL
005 AM MIC GAIN
006 AM STEP
007 APO TIME
008 ARTS BEEP
009 ARTS ID
010 ARTS IDW
011 BEACON TEXT 1
012 BEACON TIME
013 BEEP TONE
014 BEEP VOL
015 CAR LSB R
016 CAR LSB T
017 CAR USB R
018 CAR USB T
019 CAT RATE
020 CAT/LIN/TUN
021 CLAR DIAL SEL
022 CW AUTO MODE
023 CW BFO
024 CW DELAY
025 CW KEY REV
026 CW PADDLE
027 CW PITCH
028 CW QSK
029 CW SIDE TONE
030 CW SPEED
031 CW TRAINING
032 CW WEIGHT
033 DCS CODE
034 DCS INV
035 DIAL STEP
036 DIG DISP
037 DIG GAIN
038 DIG MODE
039 DIG SHIFT
The Menu System allows you to customize a wide variety of transceiver performance aspects and operating characteristics.
Once you have gone through the various Menu customization procedures initially, you will find that you will not have to resort
to them frequently during everyday operation.
MENU OPERATION
1) In step 3 above, if you press the [HOME] key
momentarily, it will reset the setting of that
Menu Item to its factory-default value.
2) In step 4 above, if you press the [C] key momentarily,
you will exit to normal operation without saving the new
setting.
3) In step 2 above, press the [A] key momentarily, The
“hyphen” in the Menu channel number will change to
become a “dot”; this shows that this Menu now is not in-
cluded in the recall the Menu Item loop.
MENU OPERATION
1. Press and hold in the
[
F
]
key for one second. The Menu
Item number and a title for the Menu Mode will appear
in the display.
2. Rotate the MEM/VFO CH knob to select the Menu Item
you wish to work on.
3. When you have chosen the desired Menu Item number,
rotate the DIAL knob to change the value or condition
for the Menu Item.
4. When you have made your selection, press and hold in
the
[
F
]
key for one second to save the new setting and
exit to the normal operation.
56

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu FT-897D bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu FT-897D in de taal/talen: Engels als bijlage per email.

De handleiding is 3,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info