478500
50
Verklein
Vergroot
Pagina terug
1/76
Pagina verder
Page 48 FT-897D OPERATING MANUAL
SCANNING OPERATION
SCANNING FEATURES
Scan-Resume Choices
Scanning operation requires that you have the FT-897D’s
audio squelched. The transceiver then “assumes” that the
opening of the squelch corresponds to the discovery of a
signal you may wish to listen to.
Once the scan has been halted, one of three things may hap-
pen:
TIME (default action): In this mode, the transceiver pauses
on the signal and stays locked on its frequency for
five seconds. Thereafter, scanning will resume
whether or not the other station’s transmission has
ended. The pause time is adjustable from 1 to 10 sec-
onds via Menu Mode No-078
[
SCAN RESUME
]
.
BUSY:In this mode, the scanner will halt until the other
station’s transmission ceases (at which point the
squelch will close). One second after the squelch
closes, scanning resumes automatically.
STOP:In this mode, the scanner will find a signal, and lock
on that frequency without resuming the scan.
To choose the Scan-Resume mode:
1. Press and hold in the
[
F
]
button for one second to acti-
vate the Menu mode.
2. Rotate the MEM/VFO CH knob to select Menu Mode
No-077
[
SCAN MODE
]
.
3. Rotate the DIAL knob to select the desired Scan-Resume
mode.
4. Press and hold in the
[
F
]
button for one second to exit
the Menu mode.
This transceiver contains a wide variety of scanning capa-
bilities. Whether you are in the VFO mode or one of the
memory modes, scanning operation is fundamentally iden-
tical in all configurations, but with the following differences:
In the VFO mode, scanning causes the transceiver to
sweep up or down the band, pausing or halting on any
signal encountered;
In the Memory mode, the scanner will scan the pro-
grammed memories, and can be instructed to skip cer-
tain memories during scanning;
In the Programmable Memory Scan (PMS) mode, the
scanner will scan the band within user-programmed fre-
quency limits.
Scanning Operation
In order for the FT-897D to scan automatically, the Squelch
must be set so that the background noise is silenced, be-
cause the command to “Stop Scanning” driven by the same
circuit that causes the green “Busy” LED to light up (when
noise or a signal is received).
1. Set the SQL knob to the point where background noise
is silenced. A typical setting, for effective scanning op-
eration, will be at 12 o’clock or slightly clockwise from
this position.
2. Set the transceiver into the operating configuration in
which you wish to scan (VFO or Memory; PMS will be
described later).
3. Press the
[
F
]
key momentarily, then rotate the MEM/
VFO CH knob, as needed, until Multi Function Row
“g”
[
SCN, PRI, DW
]
appears on the display.
4. Press the
[
A
](
SCN
)
key momentarily to start upward scan
(toward higher frequencies or higher memory channel
numbers).
5. Rotate the DIAL knob or MEM/VFO CH knob counter-
clockwise to toggle the scanning direction downward.
6. The scanner will now cause the transceiver to increment
in the chosen direction until a signal is detected. When a
signal is encountered which opens the Squelch, it will
do different things, depending on the operating mode:
In the FM/AM modes, the transceiver pauses on the
signal and stays locked on its frequency for five sec-
onds. Thereafter, scanning will resume whether or
not the other station’s transmission has ended. While
the transceiver is in the “Pause” condition, the deci-
mal points in the frequency display area will blink.
See “Scan-Resume Choices” on next chapter for de-
tails of how to customize the resumption of scanning.
In the SSB/CW modes, the scanner will slow down
(but wonn’t stop).
7.
Press the PTT switch on the microphone to cancel scanning.
You may also press and hold in either the [UP]
or [DWN] key on the microphone for one sec-
ond to initiate upward or downward scanning,
respectively, if Menu Mode No-058 [MIC SCAN] is set to
“ON.”
50

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu FT-897D bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu FT-897D in de taal/talen: Engels als bijlage per email.

De handleiding is 3,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info