478500
45
Verklein
Vergroot
Pagina terug
1/76
Pagina verder
Page 43FT-897D OPERATING MANUAL
FC-30 AUTOMATIC ANTENNA TUNER OPERATION
The optional FC-30 Automatic Antenna Tuner provides au-
tomatic tuning of a coaxial line so as to present a nominal
50 impedance to the FT-897Ds HF/50 MHz antenna port.
Before operation can begin, you must instruct the FT-897D’s
microprocessor that the FC-30 is being used. This is done
using the Menu Mode:
1. Press and hold in the
[
F
]
key for one second to activate
the Menu mode.
2. Rotate the MEM/VFO CH knob to recall Menu Mode
No-001
[
EXT MENU
]
, then rotate the DIAL to change
the setting to “ON” to enable the extended Menu Mode.
3. Rotate the MEM/VFO CH knob to recall Menu Mode
No-020
[
CAT/LIN/TUN
]
. The default setting for this
Menu is “CAT.” Rotate the DIAL to change the setting to
TUNER.”
4. Press and hold in the
[
F
]
key for one second to save the
new setting and exit, then turn the transceiver off.
5. Set up the FC-30 and FT-897D per the illustration, then
turn on the transceivers power again. Do not set up
the FC-30 and FT-897D before changing the
Menu Mode, item No-020
[
CAT/LIN/TUN
]
.
6. Press and hold in the
[
F
]
key for one second to activate
the Menu mode.
7. Rotate the MEM/VFO CH knob to recall Menu Mode No-
085
[
TUNER/ATAS
]
. The default setting for this Menu is
OFF.” Rotate the DIAL to change the setting to “TUNER.”
8. Press and hold in the
[
F
]
key for one second to save the
new setting and exit.
Operation is similar to the procedure for the ATAS-100/-120:
1. Press the
[
F
]
key, as needed, to recall Multi Function
Row “k”
[
TUNE, DOWN, UP
]
.
2. Press the
[
A
](
TUNE
)
key to turn the FC-30 on. “Paren-
theses” will appear on both sides of the “TUNE” indica-
tion, and the “TUNR” will appear on the LCD.
3. Press and hold in the
[
A
](
TUNE
)
key to initiate automatic
tuning. The FT-897D transmitter will be activated, a car-
rier signal will be sent out, and the coils and capacitors in
the FC-30 will be selected/adjusted for optimum SWR.
When tuning is complete, the transmission will cease, and
you will be ready for operation on this frequency.
Tuning data will be stored in the FC-30’s
Memory system. See the discussion below for
details on how this works.
TRANSMITTER OPERATION
Antenna Tuner Memory System
The FC-30, working in concert with the FT-897D, can store
impedance matching data in its micro-computer memory, so
as to provide instant adjustment as you transmit in different
areas of a particular band. A total of 100 memories are pro-
vided: 11 of these are “general” memories apportioned one
per band, while the remaining 89 are allocated for specific
frequency data within the various bands, with the capability
to resolve new tuning data every 10 kHz. A few guidelines
should be noted regarding the FC-30s memory system:
Tuning data is stored when you make an active effort to store
it by pressing and holding in the
[
A
](
TUNE
)
key for one
second. Although the tuner will automatically activate itself
if it encounters more than 1.5:1 SWR, this memory will not
be stored unless you have pressed the
[
A
](
TUNE
)
key for
one second. This allows you to store your favorite operating
frequency areas into tuner memory without tying up memory
space with matching data on seldom-used frequencies.
If the FC-30 cannot resolve a satisfactory match because
the SWR is above 3:1 (2:1 on the 50 MHz band), the tuning
process will stop, and no memory data will be stored. How-
ever, you may wish to move frequency a few kHz, then press
the
[
A
](
TUNE
)
key again for one second, as slight changes
in the reactance may allow a match to be obtained. Then go
back to the original frequency and try again.
Another technique which may allow matching in some situ-
ations is to add a few feet or meters of coaxial cable on the
“antenna side” of the FC-30. This will change the imped-
ance transformation taking place in the coaxial cable, possi-
bly moving the impedance presented to the FC-30 into an
acceptable range. Note that this is not changing the actual
antenna SWR, but only the impedance “seen” by the FC-
30s matching circuits.
If your antenna system presents an SWR of less than 1.5:1,
you may wish to turn off the antenna tuner, as full transmit-
ter power will be delivered to the antenna system without
intervention by the FC-30.
If the impedance encountered by the FC-30 exceeds 3:1,
and the “HI SWR” icon is illuminated, the microprocessor
will not retain the tuning data for that frequency, as the FC-
30 presumes that you will want to adjust or repair your an-
tenna system so as to correct the high SWR condition.
GND
DATA
ACC KEY
ANT
INPUT
22A
TRX
Supplied
Coaxial Cable
To 144MHz/ Antenna430MHz
CA T
/LINEAR
CTRL
144MHz/430MHz
HF/50MHz
ANT
To HF/50MHz Antenna
Control Cable
45

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu FT-897D bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu FT-897D in de taal/talen: Engels als bijlage per email.

De handleiding is 3,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info