478500
41
Verklein
Vergroot
Pagina terug
1/76
Pagina verder
Page 39FT-897D OPERATING MANUAL
TRANSMITTER OPERATION
PSK31 Operation
Two dedicated PSK31 modes are available, one each for
USB-side and LSB-side injection. For BPSK work, the in-
jection does not matter, but for QPSK the two working sta-
tions must use the same sideband.
Connect the FT-897D to your computers sound card or
interface, per thenillustration.
Setup for PSK31 operation is basically identical to that pre-
viously described for RTTY operation. As before, use the
“DIG” mode. However, in Menu Mode No-038
[
DIG
MODE
]
, select “PSK31-L” (for LSB injection) or “PSK31-
U” (for USB injection). As with RTTY, Menu #38 may be
used to set the drive to the transmitter. And the YF-122C
500 Hz filter or YF-122CN 300 Hz filter may also be uti-
lized, as described previously.
“USER” DEFINED DIGITAL MODES
Also provided in the FT-897D are two convenient “USER”
Digital modes, one each providing USB- and LSB-side in-
jection, which may be used for SSTV, Fax, Pactor, and other
digital operating modes.
Here is an example involving the configuration of the USER
mode for JT44 (WSJT) operation with USB-side injection
(as opposed to LSB injection, used in the default “RTTY”
mode):
1. Use Menu Mode No-038
[
DIG MODE
]
to set the Digital
mode to “USER-U.”
2. Press the MODE
(
)
/MODE
(
)
key, as needed, to se-
lect the DIG operating mode (the “DIG” icon will appear
on the display).
3. Now use Menu mode to configure the transceivers pass-
band response. Once in the Menu mode, rotate the MEM/
VFO CH knob to select Menu Mode No-039
[
DIG
SHIFT
]
, and rotate the DIAL knob to set the desired BFO
offset. (a center frequency for the receiver response). For
WSJT use, a setting of about “+1500” will be a good
starting point.
4. Finally, depending on how you wish the display to re-
spond, you may program in a corresponding display shift,
using Menu Mode No-036
[
DIG DISP
]
.
5. Remember to press and hold in the
[
F
]
key for one sec-
ond when exiting the Menu mode.
The setup of the AFSK drive level is identical to that de-
scribed previously for RTTY operation.
The USER-L and USER-U Digital modes
should allow you to operate on any SSB-based
AFSK Digital mode. Note that the “PSK31”
configurations will also work well for many Digital oper-
ating situations.
DIGITAL MODE OPERATION
(
SSB-BASED AFSK
)
Packet (1200/9600 bps FM) Operation
The FT-897D is designed for operation on either 1200 bps
or 9600 bps packet, and setup is similar to that described
previously for SSB-based modes. A separate Data input ad-
justment is provided, allowing you to optimize the devia-
tion on the FM Packet modes separately from the levels set
for SSB-based Digital modes. The RX-Data
output lines are
fixed-level outputs, not affected by the setting of the AF Gain
control.
1. Connect your TNC to the FT-897Ds rear-panel DATA
jack, per the illustration.
Note that different connections are used for 1200 bps
and 9600 bps Packet.
PTT
DATA IN
GND
DATA
OUT
DATA
IN
PTT
DATA OUT
(1200bps)
DATA OUT
(9600bps)
2. Use Menu Mode No-073
[
PKT RATE
]
to select the de-
sired Packet mode.
Once you have entered the Menu and have selected Menu
Mode No-073
[
PKT RATE
]
, rotate the DIAL knob to
select either “1200” or “9600” (bps) as the Packet rate.
3. Press the MODE
(
)
/MODE
(
)
key, as needed, to se-
lect the PKT operating mode (the “PKT” icon will ap-
pear on the display).
You are now set up for reception on Packet. If you are oper-
ating on 1200 bps, try now to connect to another station or
node; you may well find that the drive level needs no further
adjustment. If, however, you are having trouble connecting
due to insufficient or excessive drive from the TNC to the
FT-897D, use Menu Mode No-071
[
PKT 1200
]
(for 1200
bps Packet) or No-072
[
PKT 9600
]
(for 9600 bps Packet)
to set the drive. Use your terminal software’s “test” protocol
to send out test tones, and adjust the deviation by rotating
the DIAL knob, which will vary the data input level to the
FT-897Ds modulator. Remember to press and hold in the
[
F
]
key for one second when adjustments are completed, so
as to save the new setting for Menu Mode No-071
[
PKT
1200
]
or No-072
[
PKT 9600
]
.
The 9600 bps Packet deviation setting is very criti-
cal to successful operation, and it can only be
accomplished using a calibrated deviation meter;
the optimum setting is usually ±2.75 kHz (±0.25 kHz). For
1200 bps, the optimum level is much less critical, with the
optimum deviation being between ±2.5 kHz and ±3.5 kHz.
41

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu FT-897D bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu FT-897D in de taal/talen: Engels als bijlage per email.

De handleiding is 3,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info