478500
28
Verklein
Vergroot
Pagina terug
1/76
Pagina verder
Page 26 FT-897D OPERATING MANUAL
RECEIVER ACCESSORIES
NOISE BLANKER
The IF Noise Blanker may be useful in reducing or elimi-
nating some types of impulse noise, especially noise gener-
ated by automotive ignition systems.
1. Press the
[
F
]
key momentarily, then rotate the MEM/
VFO CH knob, as needed, until Multi Function Row “l”
[
NB, AGC, OFF
]
appears on the display.
2. Press the
[
A
](
NB
)
key to activate the Noise Blanker. Pa-
rentheses will appear on both sides of the “NB” selec-
tion, indicating that the Noise Blanker is now on.
3. To adjust the blanking level, press and hold in the
[
A
](
NB
)
key for one second. This instantly activates
Menu Mode No-063
[
NB LEVEL
]
, which allows adjust-
ment of Noise Blanking Level. Rotate the DIAL knob to
set a higher or lower blanking level (on a scale of 0 to
100). When done, press and hold in the
[
F
]
key for one
second to save the new setting and return to normal op-
eration.
4. Press the
[
A
](
NB
)
key again to turn the Noise Blanker
off.
IPO
(
INTERCEPT POINT OPTIMIZATION
)
The IPO feature bypasses the receiver RF preamplifier,
thereby eliminating the preamp’s gain. This feature is not
available on the 144 MHz and 430 MHz bands.
1. Press the
[
F
]
key momentarily, then rotate the MEM/
VFO CH knob, as needed, until Multi Function Row
“m”
[
IPO, ATT, NAR
]
appears on the display.
2. Press the
[
A
](
IPO
)
key to bypass the receiver input pream-
plifier. Parentheses will appear on both sides of the “IPO
selection, and the “ ” icon will appear on the display.
indicating that the preamp is now disengaged from the
receiver circuit.
3. Press the
[
A
](
IPO
)
key once more to re-activate the
preamp.
On the bands below 14 MHz, the input pream-
plifier is rarely necessary, and activation of the
IPO feature will provide substantial protection
against intermodulation and other problems associated
with strong signal input to the receiver. Rule of thumb: so
long as the S-meter is moving on background noise, addi-
tional front-end gain is not necessary.
ATT
(
FRONT END ATTENUATOR
)
The Attenuator will reduce all signals (and noise) by 10 dB,
and it may be used to make reception more pleasant under
extremely noisy conditions. This feature is not available on
the 144 MHz and 430 MHz bands.
1. Press the
[
F
]
key momentarily, then rotate the MEM/
VFO CH knob, as needed, until Multi Function Row
“m”
[
IPO, ATT, NAR
]
appears on the display.
2. Press the
[
B
](
ATT
)
key to activate the Attenuator. Pa-
rentheses will appear on both sides of the “ATT” selec-
tion, and the “ ” icon will appear on the display.
3. Press the
[
B
](
ATT
)
key once more to switch the Attenu-
ator out of the receiver front end circuit. Signals will
again be received at a level 10 dB louder than was the
case when the Attenuator was engaged.
DSP BANDPASS FILTER
In the SSB mode, the receivers selectivity may be enhanced
via the DSP Bandpass Filter.
1. Press the
[
DSP
]
key momentarily. This instantly acti-
vates Multi Function Row “p”
[
DNR, DNF, DBF
]
.
2. Press the
[
C
](
DBF
)
key to activate the DSP Bandpass
Filter. Parentheses will appear on both sides of the “DBF
selection, and the “DSP” will appear at the center top
on the display. You will notice a decrease in both back-
ground noise and interference, if any is present.
3. The bandwidth of the DSP filter may be modified, to
customize the bandwidth to your operating needs. To
adjust the Low-Cut and High-Cut characteristics of the
DSP Bandpass Filter:
Press and hold in the
[
C
](
DBF
)
key for one second.
This instantly activates Menu Mode No-047
[
DSP
LPF CUTOFF
]
, which allows adjustment of the High-
Cut (Low-Pass) filter.
Turn the DIAL, as desired, to adjust the high-fre-
quency cutoff of the DSP Bandpass Filter.
Now rotate the MEM/VFO CH knob one click
counter-clockwise to select Menu Mode No-047
[
DSP HPF CUTOFF
]
, which allows adjustment of the
Low-Cut (High-Pass) filter.
Turn the DIAL, as desired, to adjust the low-frequency
cutoff of the DSP Bandpass Filter.
When done, press and hold the
[
F
]
key for one sec-
ond to save the new setting(s) and return to normal
operation.
4. Press the
[
C
](
DBF
)
key once more to disable the DSP
Bandpass Filter.
HPF
100 Hz~1000 Hz
LPF
1000 Hz~6000 Hz
28

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu FT-897D bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu FT-897D in de taal/talen: Engels als bijlage per email.

De handleiding is 3,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info