478500
26
Verklein
Vergroot
Pagina terug
1/76
Pagina verder
Page 24 FT-897D OPERATING MANUAL
LOCKING FRONT PANEL CONTROLS
The front panel LOCK button allows you to disable the DIAL
and/or the front panel controls.
RECEIVER ACCESSORIES
BATT- A
BATT- B
BAND
MODE
CLARAF
LOCK
PHONE
MIC
SQL
/RF
MEM/VFO CH
DWN UP
V/M
DSP
UP
DSP
F
LOCK
In the transceivers default configuration, pressing the LOCK
button disables just the DIAL, while the other keys and
switches are unaffected.
To lock out the remainder of the controls and the MEM/
VFO CH knob, use Menu Mode No-054
[
LOCK MODE
]
;
1. Press and hold in the
[
F
]
key for one second to enter the
Menu mode.
2. Rotate the MEM/VFO CH knob so as to recall No-054
[
LOCK MODE
]
.
3. Rotate the DIAL to select the desired configuration:
DIAL: Locks DIAL knob only.
FREQ: Locks front panel keys and knobs related to fre-
quency control (such as BAND
(
DWN
)
and
BAND
(
UP
)
key,
[
A
](
A/B
)
key., etc.)
PANEL: Locks all front panel keys and knobs (except
POWER and LOCK keys)
ALL: Locks all front panel keys and knobs (except
POWER and LOCK keys) and microphone
keys.
4. When you have made your selection, Press and hold in
the
[
F
]
key for one second to save the new setting and
exit to normal operation.
When the controls are locked out, press the LOCK button
once more to release them to normal operation.
CLARIFIER
(
RECEIVER INCREMENTAL TUNING
)
The Clarifier (RIT) allows you to set an offset of up to ±9.99
kHz of the receive frequency relative to your transmit fre-
quency. To achieve a wider offset than this, you may use the
“Split” operating mode, described later.
1. Press the CLAR/IF SHIFT button momentarily to acti-
vate the Clarifier function.
2. Turn the CLAR knob, which allows the receiver fre-
quency to be varied over a range of ±9.99 kHz.
3. When the receiving frequency is
higher than transmit frequency, the
(within 1 kHz)” or “ (exceed 1
kHz)” icon will appear at the right
of the frequency display. Similarly,
when the receiving frequency is
lower than transmit frequency, the
(within 1 kHz)” or “ (exceed 1
kHz)” icon will appear at the right
of the frequency display. When the
receiving frequency is equal to trans-
mit frequency (Clarifier offset is
zero) while the Clarifier is activated,
the “” icon will appear at the right
of the frequency display.
4. To turn the Clarifier off, again press
the CLAR/IF SHIFT button mo-
mentarily. When you turn the Clari-
fier back on, the offset previously
stored will still be applied.
5. To reset the Clarifier offset to zero, turn the Clarifier off,
then turn the DIAL by any amount. The Clarifier will
reset to zero after the first “step” of the DIAL.
1) If you leave the Clarifier on, moving the DIAL
will not cause the offset to be cancelled.
2) You may change the knob that controls the
Clarifier offset from the DIAL to the MEM/VFO
CH knob via Menu Mode No-021
[
CLAR DIAL SEL
]
.
[
TX<RX
(
within 1 kHz
)]
[
TX=RX
(
Simplex
)]
[
TX>RX
(
within 1 kHz
)]
[
TX>RX
(
exceed 1 kHz
)]
BATT- A
BATT- B
BAND
MODE
CLARAF
LOCK
PHONE
MIC
SQL
/RF
MEM/VFO CH
DWN UP
V/M
DSP
UP
DSP
F
CLARCLAR/IF SHIFT
26

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Yaesu FT-897D bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Yaesu FT-897D in de taal/talen: Engels als bijlage per email.

De handleiding is 3,3 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info