523453
11
Verklein
Vergroot
Pagina terug
1/98
Pagina verder
11
en
Cable
1
Attention!
Electric shock through cable damage
When the cable is cut through or damaged, the safety fuse
does not always trip.
z
Do not touch cable before pulling out the power plug out of
the socket.
z
A damaged cable must be completely replaced. Repairing
the cable with insulating tape is not permitted.
z
Repairs to the cable should be performed only by an expert.
z
Do not scrape against corners, spikes or sharp objects.
z
Do not squeeze the cable between door jams or through win-
dows.
z
Switchgears must not be removed or bridged.
z
Use only extension cable not lighter than rubber hose,
type HO 7 RNF, minimum cross section 3 x 1.5 mm
2
, length:
max. 25 m.
z
Cables have to be protected against splashing water.
z
Do not carry or suspend the tool by the power cable and do
not pull the cable to disconnect the plug from the socket.
Keep the cable away from heat sources, oil, sharp edges and
moving tool parts.
Damaged or entangled cables increase the
risk of electric shock.
Handling
z
Keep the working area tidy and ensure that it is properly illu-
minated.
Working in cluttered or poorly lit areas can lead to acci-
dents.
z
Do not use the electric tool in explosive atmospheres contai-
ning flammable liquids, gases or dusts.
Electric tools might
generate sparks that can ignite dust or vapors.
z
When working with the electric tool, ensure that your full at-
tention is on the task in hand, do not let yourself be distrac-
ted and apply common sense. Do not use the electric tool
when you are tired, or when you are under the influence of
drugs alcohol or medication.
Even brief moments of inattention
can lead to serious injury.
z
Ensure before starting the appliance that the feed hopper is em-
pty.
z
Keep your head and body away from the feed opening.
z
Do not place hands, other parts of the body and clothes in the
feed hopper, discharge channel or near moving parts.
z
Always ensure that you are balanced and on firm footing.
z
Do not stretch forward. Never place yourself higher than the ap-
pliance when feeding in material.
z
When commissioning the appliance always stand outside the di-
scharge area.
z
When feeding in material ensure in particular that no metal,
stones, bottles, cans or other foreign bodies are included.
z
If foreign bodies should enter the cutting tool or should the appli-
ance make unusual noises, switch the motor off immediately and
allow the appliance to stop gradually. Remove the mains plug and
carry out the following procedures:
Check the appliance for damage
Check that the parts are firmly seated and tighten if required
Repair or replace any damaged parts (only use original WOLF-
Garten spare parts).
z
Do not allow processed material to accumulate within the dischar-
ge area. This could compromise correct discharge and lead to the
kickback of material through the feed opening.
z
If the appliance is blocked, switch the motor off and remove the
mains plug before starting to clean.
z
Ensure that the motor is free from waste and other accumulations
to protect the motor from damage or overheating.
z
Ensure that all covers and baffles are in place and in correct wor-
king order.
z
Do not transport the appliance when the motor is running.
z
Switch the motor off as soon as you leave the workstation and re-
move the mains plug.
z
Do not tilt the appliance when the motor is running.
Maintenance and storage
z
If the appliance is to be switched off for maintenance, storage or
accessory replacement purposes, ensure that the energy source
is switched off and that the mains plug is removed. Ensure that
the moving parts are at a standstill. Allow the appliance to cool
before maintenance, adjustment etc.
z
When servicing the cutting tool, ensure that it can still always run
on, even when the motor is switched off.
Disposal
Mount handle assembly
z
See illustrations
Operation
Times of operation
z
Please consult regional/local regulations.
z
Inquire about the operating times at your local regulatory agency.
Connect to the socket (230 Volt, 50 Hz)
z
Only connect the equipment to sockets which are shielded with a
16 Amp. fuse (inertial or LS switch type B).
3
Note: Residual current protection device
These safeguards provide protection against severe injuries
resulting from touching damaged cables, insulation defects
and in some cases cables that conduct electricity.
z
We recommend that the equipment only be plugged into a
power socket, which is protected by a residual current pro-
tection device (RCD) with a residual current of no more than
30 mA.
z
Retrofit kits are available for old installations. Consult an
electrician.
Power tools do not belong in household garbage.
Bring the device, accessories and packaging to an en-
vironmentally-friendly recycling location.
A
B
C
11

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

WOLF-Garten-SDE-2800-EVO

Zoeken resetten

  • Ik heb het apparaat volgens de gebruiksaanwijzing in elkaar gezet en de opvangbak goed geplaatst. De stroomvoorziening heb ik na gekeken maar de hakselaar doet niks. Hij gaat niet aan, maakt ook totaal geen geluid, niks doet ie. Gesteld op 15-2-2023 om 12:45

    Reageer op deze vraag Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw WOLF-Garten SDE 2800 EVO bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van WOLF-Garten SDE 2800 EVO in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Pools, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 1,97 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info