537310
37
Verklein
Vergroot
Pagina terug
1/396
Pagina verder
HSA 66, HSA 86
English
35
Inspect the hedge and work area to
avoid damaging the cutting blades:
Remove stones, rocks, pieces of
metal and other solid objects.
When working close to the ground,
make sure that no sand, grit or
stones get between the blades.
Take particular care when cutting
hedges next to or against wire
fences.
To avoid the risk of electrocution, do not
touch electric power lines – never cut
through electric power lines.
To reduce the risk of fire, always clean
plant residue, chips, leaves and excess
lubricant off the motor.
When working at heights:
Always use a lift bucket
Never work on a ladder or in a tree
Never work on an insecure support
If the hedge is very dusty or dirty, spray
the blades with STIHL resin solvent from
time to time during cutting. This helps
reduce blade friction as well as the
aggressive effects of sap and the build-
up of dirt particles.
The dust that occurs during operation
may be harmful to health. If dust levels
are very high, wear a suitable respirator.
Do not leave the machine outdoors in
the rain.
Take special care in slippery conditions,
on slopes or uneven ground.
Work calmly and carefully – in daylight
conditions and only when visibility is
good. Stay alert so as not to endanger
others.
Clear away fallen branches, scrub and
cuttings.
Watch out for obstacles: Roots, tree
stumps or holes which could cause you
to trip or stumble.
Be particularly alert and cautious when
wearing hearing protection because
your ability to hear warnings (shouts,
alarms, etc.) is restricted.
To reduce the risk of accidents, take a
break in good time to avoid tiredness or
exhaustion.
If your power tool is subjected to
unusually high loads for which it was not
designed (e.g. heavy impact or a fall),
always check that it is in good condition
before continuing work – see also
"Before Starting Work". Make sure the
safety devices are working properly. Do
not continue operating your power tool if
it is damaged. In case of doubt, have the
unit checked by your servicing dealer.
Before leaving the power tool
unattended: Always switch off the power
tool, set the retaining latch to ƒ and
remove the battery.
Check the cutting blades at regular short
intervals during operation or
immediately if there is a noticeable
change in cutting behavior:
Switch off the motor, move the
retaining latch to ƒ and wait for the
cutting blades to come to a
standstill, remove the battery.
Check condition and tightness, look
for cracks.
Check sharpness.
To replace the cutting blades, switch off
the power tool, move the retaining latch
to ƒ and remove the battery. This
avoids the risk of injury from the motor
starting unintentionally.
After finishing work
Always clean dust and dirt off the power
tool do not use any grease solvents for
this purpose.
Spray the blades with STIHL resin
solvent. Run the motor briefly so that the
solvent is evenly distributed.
Holding and Controlling the Power Tool
Always hold the unit firmly with both
hands on the handles. Wrap fingers and
thumbs firmly around the handles.
The drive motor is not
waterproof. Never work
with the power tool in the
rain or in wet or very
damp locations.
37

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Stihl-HSA-86

Zoeken resetten

  • ik heb de scharen van de STIKL HSA 86 gedemonteerd om deze schoon te maken. Nu heb ik een probleem met het terug plaatsen van deze. Misschien kunt U mij helpen aan een tekening van dit apparaat. bvb mijn dank. Gesteld op 24-9-2022 om 16:41

    Reageer op deze vraag Misbruik melden
  • Wat is er aan de hand als ik de hsa 86 start gaat de eerste 15 a20 seconde normaal naar daarna begind hij meer lawaai te maken aan de motor of aandrijving Gesteld op 23-8-2018 om 22:14

    Reageer op deze vraag Misbruik melden
    • Ik ben een prof. tuinaannemer met 25 jaar ervaring en werk al meer dan 15 jaar met een Pellenc haagschaar. Deze maakt na een dagje werken ook iets meer lawaai. Dat zit de tandwielkast. Heel makkelijk kan ik er smeervet en een kleine hoeveelheid vloeibare smeerolie in doen. Hierna is deze haagschaar fluisterstil. Dus, ik denk dat ook bij Stihl het stugge vet mankeert, die de tandwielen stil over elkaar laat draaien. Ik werk soms nu ook met een HSA 86, en die knettert inderdaad wel. Veel meer dan de Pellenc. Helaas is bij de HSA geen smeernippel of een gat in de tandwielkast. Ik geloof eigelijk niet in de langdurig gebruik zonder extra te kunnen smeren.

      jan Geantwoord op 17-7-2019 om 23:23

      Waardeer dit antwoord (2) Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Stihl HSA 86 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Stihl HSA 86 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 11,7 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info