781437
29
Verklein
Vergroot
Pagina terug
1/92
Pagina verder
internet: www.scheppach.com / email: service@scheppach.com / telefon: +(49)-08223-4002-99 / telefax: +(49)-08223-4002-58
29 І 92
DE GB FR DE GBDE GB FR DE GB FR DE GB FR
internet: www.scheppach.com / email: service@scheppach.com / telefon: +(49)-08223-4002-99 / telefax: +(49)-08223-4002-58
when the saw has been set up in a closed room;
when the saw is being used for longer periods
(more than half an hour per day);
when sawing oak, beech or ash.
The extraction unit must comply with the following re-
quirements:
The diameter of the extraction connection has to
t (32 mm).
Air ow volume of at least 550 m3/hr.
The vacuum at the saw‘s extraction output has to
be a minimum of 740 Pa.
The air ow volume at the saw‘s extraction output
has to be a minimum of 20 m/s.
You must comply with the specications for the use
of the extraction unit.
8. Operation
Changing the sawing mode
m DANGER
Remove the mains plug before changing the saw-
ing mode!
On delivery, the saw is in table circular saw operating
mode.
The saw has two work settings:
1. Table circular saw
2. Chop and mitre saw
Changing the combination saw must be carried
out according to the following procedure and
step by step. Otherwise, damage can be caused
to the components.
Use as chop and mitre saw (Fig. 5)
Attention! For 90° mitre cuts, the moveable stop
rail (53) must be xed in the inner position.
Open the set screw on the moveable stop rail (53)
with an Allen key and push the moveable stop rail
(53) inwards.
The moveable stop rail (53) must be locked in a po-
sition far enough from the inner position that the
distance between the stop rail (53) and the saw
blade (12) is no more than 8 mm.
Before making the cut, check that no collision could
occur between the stop rail (53) and the saw blade
(12).
Secure the locking lever again.
Important. To make miter cuts (inclined saw
head), the adjustable stop rail (53) must be xed
at the outer position.
Open the set screw (53) for the adjustable stop rail
(53) with an Allen key and push the adjustable stop
rail outwards.
The adjustable stop rail (53) must be xed far
enough in front of the innermost position that the
distance between the stop rail (53) and the saw
blade (12) amounts to a maximum of 8 mm.
Before making a cut, check that the stop rail (53)
and the saw blade (12) cannot collide.
Secure the locking lever again.
The rip fence (1) has to be installed in such a way
that the saw blade is covered. This activates switch
(A). The cover (rip fence) (1) has to be securely fas-
tened with the lock screw (18).
The specied vibration emission value has been
measured according to a standardised test proce-
dure and can be used in comparison with another
power tool.
The specied vibration emission value can also be
used for an initial assessment of the exposure.
m WARNING
The vibration emission value can vary from the speci-
ed value during actual use of the power tool, de-
pending on the way it is used.
Try to keep exposure to vibrations as low as possible.
Measures to reduce exposure to vibration are, for ex-
ample, wearing gloves when using the machine, or
by reducing the work time. All parts of the operating
cycle must be considered for this (for example: times
during which the power tool is switched off and times
when it is turned off but runs without load).
7. Set-up
m WARNING
For your own safety, only put the mains plug into the
socket when you have completed all assembly steps
and you have read and understood the safety notices
and the operating instructions.
Assembly (Fig. 4)
Lift the machine from the packaging with the help
of another person.
Set the rotary table to position and attach the
rip fence.
m NOTICE
If you are intending to attach the machine to a table
top, do not use the rubber feet.
To attach the rubber feet, carefully tilt the machine
to the right so it is supported by the motor.
Insert the nut (34) into the underneath of the rub-
ber feet.
Insert the Allen screw (32) into the feet of the ma-
chine from above. Secure the rubber feet (33) with
the nut (34) inserted previously on the screw (32).
Attach the rubber feet only nger-tight.
Tighten the screw with the Allen key.
Position the machine on a level surface:
All four feet of the machine have to be positioned
rmly and securely on the surface.
The ideal height for such a surface is approx.
800 mm.
The saw always has to be stable and secure
even when larger work pieces are cut.
Store the packaging safely for potential use at a
later stage or dispose of it in an environmentally
friendly way according to usual material separation.
Assembling the work piece clamping device (Fig.
1)
Loosen the mitre lock (16) and attach the work
piece clamping device (15) to the left or right of
the xed saw bench.
Afterwards, retighten the mitre lock (16).
Attaching the extraction unit
Particles from certain timber types (e.g. beech, birch,
ash) can cause harm when inhaled. Therefore, use
an extraction unit:
GB
29

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach HM100T bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach HM100T in de taal/talen: Duits, Engels, Pools, Zweeds, Noors als bijlage per email.

De handleiding is 6,16 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info