781437
28
Verklein
Vergroot
Pagina terug
1/92
Pagina verder
28 І 92
GB FR DE GB FR DE GB FR DE GB FR DE GB FR
internet: www.scheppach.com / email: service@scheppach.com / telefon: +(49)-08223-4002-99 / telefax: +(49)-08223-4002-58
Working on particular timber such as beech and MDF
can cause dangerous dust during sawing.
Therefore, a dust extraction unit must be used.
6. Technical Data
HM100T
AC motor 220 - 240 V ~ 50Hz
Performance S1 1600 Watt
S6 25%* 1800 Watt
Idle speed n05000 min-1
Carbide saw blade ø 254 x ø 30 x 3mm
Number of teeth 60
Extraction connection 32 mm
Table saw:
Saw table 432 x 298 mm
Cutting height 0-46 mm
Riving knife thickness 2,5 mm
Cross stop and rip fence rotatable
-60° to + 60°
Chop saw
Angular range -50° / 0°/ +60°
Mitre cut 0° to 45° to the left
Saw table 460 x 335 mm
Saw width x saw depth
at 9 110 x 70 mm
Saw width x saw depth
at 45° 70 x 70 mm
Saw width x saw depth at
2 x 45° (double mitre cut) 60 x 35 mm
Protection rating II
Weight approx. 19 kg
Subject to technical changes!
* Operating mode S6, uninterrupted, continuous op-
eration. Operation consists of a start-up time, a pe-
riod of constant load and idle time. The cycle duration
is 10 mins, the relative start-up time is 25% of the
cycle duration.
Information concerning noise emission measured ac-
cording to relevant standards:
Sound pressure LpA = 92.5 dB(A)
Sound power LwA = 105.5 dB(A)
Measurement uncertainty KpA = 3.0 dB(A)
Use hearing protection.
Noise at the work place can exceed 85 db (A). In this
case, sound protection measures are required for
the user. Being subjected to noise can cause hear-
ing loss. The overall vibration values (vector sum of
three directions) have been determined according to
EN 61029
The noise from this saw has been measured accord-
ing to DIN ENISO 3744; 11/95, E DIN EN 31201; 6/93,
ISO7960 Appendix A; 2/95.
Vibration emission value ah = 1.74 m/s2
Uncertainty Kh = 1.5 m/s2
Only ever use saw blades which have been
sharpened properly. Do not exceed the maximum
rotational speed specied on the saw blade;
Make sure you only use spacers and spindle
rings which are suitable for the intended purpose
specied by the manufacturer;
If the machine is equipped with a laser, this laser
must not be replaced by a laser of another type.
Repairs must be carried out by the laser manu-
facturer or an authorised representative;
Ensure that the upper part of the saw blade is
completely enclosed when in mitre saw mode;
Replacement and alignment of the saw blade
have to be carried out properly;
Make sure that the machine, if possible, is se-
cured to a work bench or a table.
Do not remove offcuts or other work piece parts
from the cutting area while the machine is run-
ning and the blade has not yet come to a stand-
still;
In the table circular saw mode, use a riving knife
and set it up properly; (Fig. 20)
The machine must not be used for slotting (insert
grooves);
During transport, the upper part of the saw blade
must be covered, e.g. by the upper guard, or the
saw blade must be in its lowest position;
In the table circular saw mode, the lower saw
safety device must be used and set up properly.
m WARNING
The vibration levels during operation of the pow-
er tool can deviate from the specied vibration
levels, depending on the application of the power
tool.
m WARNING
Restrict the work time and reduce the actual op-
erating time to lower the risk of vibration.
Remaining risks
Even when you use the machine for its intended pur-
pose, certain risks remain that cannot be completely
avoided. Based on the construction and set-up of the
machine, the following issues may occur:
Contact with the saw blade in an uncovered area
of the saw
Touching the rotating saw blade (cut)
Recoil of work pieces and ejection of work piece
parts
Saw blade breakage
Ejection of faulty carbide saw blade parts
Hearing damage when not using the required
hearing protection
Harmful emission of wood dust when the ma-
chine is used in a closed room
Risk of injury during tool replacement
The following factors affect noise emission:
1. material to be cut
2. type of saw blade
3. feed force
The following factors affect dust development:
1. worn saw blades
2. dust extraction units with an air speed of less than
20 m/s
3. work piece not guided properly
GB
28

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Scheppach HM100T bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Scheppach HM100T in de taal/talen: Duits, Engels, Pools, Zweeds, Noors als bijlage per email.

De handleiding is 6,16 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info