824188
7
Verklein
Vergroot
Pagina terug
1/9
Pagina verder
ninjakitchen.com.au | ninjakitchen.co.nzAUS +61 2 8801 7666 | NZ +64 800 112 660
CLEANING
Hand-Washing
Wash containers, lids and blade assembly
in warm, soapy water. Use a dishwashing
utensil with handle to avoid direct contact
with the blades. Exercise care when handling
the blade assembly as the blades are sharp.
Thoroughly rinse and air-dry all parts.
STUCK-ON INGREDIENTS IN THE
POWER NUTRI JUG & CUP
For stuck-on ingredients, such as nut
butter, rinse the jug and blade assembly
under warm water.
Next, fill the jug or cup with warm water up
to liquid fill or halfway on the cup and add
1–2 small drops of washing-up liquid.
Screw on the blade assembly and press
MIX. Twist the Power Paddle anti-clockwise
continuously while cleaning.
Then, empty contents and rinse under
warm water and wipe with a dishwashing
utensil, if needed.
12 13
CARE & MAINTENANCE
Dishwasher
Accessories are top-rack dishwasher safe
and should NOT be cleaned with a heated
dry cycle. Ensure the blade assembly and
lid are removed from the container before
placing in the dishwasher.
Motor Base
Unplug the unit before cleaning. Wipe
motor base with a clean, damp cloth. DO
NOT use abrasive cloths, pads or brushes
to clean the base.
STORAGE
For cord storage, wrap cord with hook-
and-loop fastener near the back of the
motor base. DO NOT wrap the cord around
the bottom of the base for storage.
DO NOT store blended or unblended
ingredients in the cup or jug with the blade
assembly attached. Use only the spout
lid when storing blended or unblended
ingredients in the containers.
DO NOT stack items on top of the containers.
Store any remaining attachments alongside
the unit or in a cabinet where they will not be
damaged or create a hazard.
RESETTING THE
MOTOR THERMOSTAT
This unit features a safety system that
prevents damage to the motor and drive
system should you inadvertently overload
it. If the unit is overloaded, the motor will
be temporarily disabled. Should this occur,
follow the reset procedure below.
1 Unplug the unit from the
electrical socket.
2 Allow the unit to cool for approximately
15 minutes.
3 Remove the blade assembly from the
container. Empty the container and
ensure no ingredients are jamming the
blade assembly.
IMPORTANT: Ensure that maximum
capacities are not exceeded. This is the
most typical cause of appliance overload.
NOTE: The Power Paddle in the Power
Nutri Jug is not removable.
NOTE: For best results, use a dishwasher
to remove stuck-on ingredients.
1 SMALL DROP OF WASHING-
UP LIQUID
FILL WATER HALFWAY
FILL WATER TO
240ml LIQUID FILL
1 OR 2 SMALL DROPS OF WASHING-
UP LIQUID
TROUBLESHOOTING GUIDE
WARNING: To reduce the risk of shock and unintended operation, turn power o and unplug
unit before troubleshooting.
Display reads “- -”.
If vessel is properly installed and the display reads ‘- -’, ensure the interior of the base
area is clean of any debris.
Control panel does not illuminate.
Make sure unit is plugged in. If the unit is powered on and no container is installed, the
unit will display ‘- -’. The available programs will illuminate after placing a container on
base and rotating it clockwise until it clicks into place.
Control panel doesnt turn o.
Remove container from base by rotating it anti-clockwise and lifting it up. The display
with flash ‘- -’. Unplug the power cord from the socket. If the unit remains plugged in,
the display will time out after 3 minutes of inactivity. Press any button to wake the unit.
Doesn’t mix well; ingredients get stuck.
Using the Auto-iQ programs is the easiest way to achieve great results. The pulses and
pauses allow the ingredients to settle toward the blade assembly. If ingredients are
routinely getting stuck, adding some liquid will usually help.
When filling the cup, start with fresh fruit or vegetables, then leafy greens or herbs.
Next add liquids or yoghurt, then seeds, powders or nut butters. Finally, add ice or
frozen ingredients.
If using the Power Nutri Jug, during the blending process twist the Power Paddle anti-
clockwise continuously to circulate ingredients.
Unit moves on worktop while blending.
Ensure the suction cup feet are clean and dry. Place the motor base on a smooth, clean
and level surface. Do not place motor base on a rough or unlevel surface as the suction
cup feet will not adhere properly.
Unit is dicult to remove from worktop for storage.
If the motor base is dicult to remove from the worktop or table, slide it across the
surface, then lift. Tilt the motor base to disengage the suction feet.
Lid or Hybrid Edge Blades Assembly is hard to install on the container.
Set the container on a level surface. Carefully place the lid or blade assembly on the
top of the container and align the threads so the lid/blade assembly sits flat. Twist
clockwise until you have a tight seal.
Cant remove the Power Paddle from the Power Nutri Jug Lid.
The Power Paddle in the Power Nutri Jug Lid is not removable. For cleaning
instructions, refer to the Cleaning section.
ORDERING REPLACEMENT PARTS
To order additional parts and attachments, visit ninjakitchen.com.au | ninjakitchen.co.nz
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Ninja CB150ANZ bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Ninja CB150ANZ in de taal/talen: Engels als bijlage per email.

De handleiding is 1,62 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info