Handleiding Multiplex ROYALevo9 (pagina 52 van 58) (Engels)

30282

Verklein

Vergroot

Pagina terug

1/58

Pagina verder

ROYAL evo

Seite 52

Alarm sequence:

x 10 seconds before the set alarm time: short beep

every second (È)

x When the alarm time is reached: long beep (È --- )

17.3. Timer „´ Sum“

I affects active model only

Range = 3 h 30 min

Press REV/CLR button in status display 3

(or in menu) to erase

This timer acts cumulatively, i.e. it sums the times. Once

started, it can be stopped again using the same switch,

then re-started by operating the switch once more.

Application:

Timing motor runs using throttle control as switch

You can set up the “Sum” timer to work in two different

modes:

1. Set alarm to 0:00:00

The timer begins at zero, runs forward (count-up),

adds the time and is stopped and re-started using

the assigned switch. You can reset it to zero in sta-

tus display 3 using the REV/CLR button, or in this

m e n u . I n t h i s c a s e t h e r e i s n o a l a r m .

2. Alarm not set to 0:00:00

The timer begins at the alarm time you set, runs

backward (count-down) and sounds the alarm

when the selected time has elapsed.

Alarm sequence:

x starting 5 min before the set alarm is reached:

short double beep every minute (ÈÈ)

x 5 seconds before the set alarm time:

short double beep every second (ÈÈ)

x When the alarm time is reached:

long double beep (È --- È ---)

17.4. Sub-menu „¶¶ Interval“

I affects active model only

Range = 3 h 30 min

Automatic erase at every re-start

With this timer you can call up the set interval as often

as you like.

The timer starts running at the set alarm time, runs

backward (count-down) and sounds the alarm when the

selected time has elapsed.

If the switch is at the ON position at the end of the alarm

time, the interval re-starts.

If the switch is at the OFF position at the end of the

alarm time, the timer continues to count up until the

maximum value is reached (4 h 30 min).

Alarm sequence:

x 1 second before the set alarm time:

short triple beep (ÈÈ È)

x When the alarm time is reached:

long triple beep (È --- È --- È)

18. Main menu „Memory“ I

The ROYALevo has 20 or 36 model memories, depend-

ing on the version you have purchased. The memory

spots are numbered continuously. You can also enter a

name with up to 16 characters for each model memory.

The model data is stored in an area of non-volatile me-

mory, and cannot be lost even if you disconnect the

transmitter battery from the transmitter.

In addition to memory management (switching, copy-

ing, erasing) you can also use this menu to create new

models (Î 18.6.) and manage the flight phases you set

up (Î 18.4.).

18.1. Sub-menu „Select model“

(change memory)

When you move to this sub-menu, the screen displays a

list showing all the model memories. The top of a typi-

cal list might look like this:

The active model memory is marked with the letter x.

An empty model memory is marked with --------.

Vacant memories can be managed, but not activated.

To change models simply select the memory you wish

to use, then press the 3-D digi-adjustor or the ENTER

button.

18.2. Sub-menu „Copy“

In this menu you can copy all the setup values relating

to the transmitter controls, mixers, servos, timers, model

name and trims.

The copy process is carried out in four stages:

1. Select the model which is to be copied.

This can be any model.

2. Confirm your selection with the 3-D digi-adjustor

or ENTER button. After the model name the letter

”c” (copy) appears.

3. Seek the destination

The model name and the “c” are carried along with

you during the search.

4. Confirm the destination with the 3-D digi-adjustor

or ENTER button.

x If the destination memory is empty, the copy

process is carried out immediately.

x If the destination memory already contains data,

you will see the security query:

“Overwrite existing model?”

x At this point you can interrupt the copy process

by pressing the ENTER button or the 3-D digi-

adjustor.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Multiplex ROYALevo9 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Andere handleiding(en) van Multiplex ROYALevo9

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info