561578
79
Verklein
Vergroot
Pagina terug
1/84
Pagina verder
Operating Instructions
Page 77
ENGLIS
H
Moving to the START1 menu:
4 to MENU, r (SETUP appears),
3 to TIMER, r (START1 appears),
r
Start time for Timer 1 in minutes : seconds
The first number of the current start time flashes. Use
the 3-D digi-adjustor to set the “tens” of minutes. A brief
press r on the 3-D digi-adjustor takes you on to the
next digit.
Once you have set the “single second digits”, a brief
press r on the 3-D digi-adjustor concludes the process.
Important: the current time is stored.
The current time of Timer 1 is stored when you switch
the transmitter off. If you want the set time to start
again next time you switch on, you must first reset
Timer 1 in the INFO 2 or INFO 3 menu (long press
ª on the 3-D digi-adjustor).
If the assigned switch is at the ON position when you
switch the transmitter on again, Timer 1 immediately
resumes counting.
19.2. Timer 2
Timer 2 is ideal for recording the overall flight time. It
always starts at 00:00. The transmitter control selected
as the timer switch can start Timer 2, but it cannot stop
it again.
Timer 2 runs to a maximum of 99 minutes, 59 seconds.
Timer 2 can be started, for example, when the throttle
is advanced for the first time, when the tow-release is
operated, or when you operate the PH switch to switch
from the launch setting to normal flight.
19.2.1. Assigning a timer switch
Menu: (
TIMER) T2 SW
Example 1: starting Timer 2 using the THROTTLE
In this case the switch is assigned using the method
described in section Î 19.1.1.
Example 2: starting Timer 2 using the PH switch
Requirements:
The model must be programmed with flight phases.
Flight phase 1 is the “launch setting”, and flight phase 2
is “normal flight”.
The following example shows how to start Timer 2 (with
the stated requirements fulfilled), when you switch for
the first time from the “launch setting” to “normal flight”.
Moving to the T2 SW menu:
4 to MENU, r (SETUP appears),
3 to TIMER, r (START1 appears),
3 to T2 SW r
No switch Switch 4
Move the PH switch quickly to and fro until code num-
ber 4 appears. The hyphen following the colon indi-
cates the switch position which triggers the timer.
Switch 4 Marker Switch position
Now move the PH switch to the position which is re-
quired to trigger the timer (in our illustration Phase 2).
A brief press r on the 3-D digi-adjustor concludes the
process. The flashing ceases, and the setting is stored.
19.2.2. Stopping Timer 2, or resetting it to 00:00
Timer 2 can only be stopped or reset if it is visible in
the bottom line of the screen. There are two methods of
doing this:
In the INFO 3 display:
Pressing the 3-D digi-adjustor at this display affects
both timers.
INFO 3 display: both timers
In the INFO 4 display:
Pressing the 3-D digi-adjustor at this display only af-
fects Timer 2.
INFO 4 display: Timer 2 only
Stop timer: r brief press on 3-D digi-adjustor
Setting timer to 00:00: ª long press on 3D digi-adjustor
Phase 3
Phase 2
Phase 1
79

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Multiplex COCKPIT SX bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Multiplex COCKPIT SX in de taal/talen: Engels als bijlage per email.

De handleiding is 1,37 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Multiplex COCKPIT SX

Multiplex COCKPIT SX Gebruiksaanwijzing - Nederlands - 17 pagina's

Multiplex COCKPIT SX Gebruiksaanwijzing - Nederlands - 149 pagina's

Multiplex COCKPIT SX Gebruiksaanwijzing - Deutsch - 83 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info