625666
14
Verklein
Vergroot
Pagina terug
1/96
Pagina verder
14
ENGLISH
ENG
can be used twice - turn if necessary.
Cutting blade
(as replacement), see
Accessories chapter.
Regrind worn cutting blade (10) if necessary
(see 12 Maintenance chapter)
7 Remove contamination, remains of leaves,
etc. (e.g. with a brush or cloth) Ensure that
the contact surfaces are particularly clean.
8
Mount cutting blade (10)
and rotate until it
engages on the drive spindle.
9
Block the cutting blade (10)
again to prevent
rotation (as described above).
10 Reinsert screw with Belleville spring (9) and
tighten clockwise with hexagon spanner
(8).
11 Remove wooden rod (or non-ferrous metal
rod).
12 Slide the enclosure (1) fully onto the cutting
blade.
13 Reinsert battery pack
(4)
.
8.4 Cleaning the cutting blades
(after every use)
Before cleaning:
Switch the machine off. Remove battery
pack (4) from machine.
Wear protective gloves.
Remove contamination, remains of blades etc.
(e.g. with a brush or cloth)
After cleaning:
Treat cutting blades with Metabo
machine care oil 6.30474 or Pump Spray 6.30475
(biologically degradable).
The maximum number of charge cycles can only
reached if an exhaustive discharge of the battery
pack is avoided. If performance diminishes,
recharge the battery pack.
9.1 Charging battery pack
Insert battery pack (4) up to stop in charging
compartment (13).
The operating display (15) flashes and the battery
is charged.
When the battery pack is fully charged, the oper-
ating display (15) lights up continuously.
The battery pack can remain in the battery charger
and is therefore always ready for use.
10.1 Warning display (14) lights up continu-
ously
Battery pack is not charged. Temperature too
high/too low. When the temperature of the
battery pack is between 0 °C and 50 °C, the
charging process begins automatically.
10.2 Warning display (14) flashes
Battery pack is defective. Remove the battery
pack immediately from the charger.
Short circuit between the charging contacts.
Check the contacts for foreign bodies.
Ensure that there are no birds brooding in your
hedge. If necessary, postpone your hedgecutting.
The chopped-up cuttings, combined with other
garden waste products, provide nutrient-rich
compost.
Unchopped cuttings placed in a natural garden
provide a useful place of retreat for small animals
such as hedgehogs.
Observe any local resting periods; your neighbour
will thank you for it.
Check that the screw and diaphragm spring
(9)
are seated securely
At regular intervals, check that the screw and
diaphragm spring (9) are seated securely using
an Allen key (8)
. The screw must always be
tight-
ened properly.
Fit a screw locking device to the
thread of the screw. The locking device will wear if
the screw is slackened and tightened frequently.
Replace the screw if necessary (order no.
341704440).
Blunt or damaged cutting blades (10)
Replace cutting blades (10) (or turn then over) if
they are blunt or damaged.
It is advisable to have blunt cutting blades (10)
sharpened in a specialist workshop. Check cutting
blades regularly for damage and have them
repaired in a specialist workshop immediately if
necessary.
9 Use of battery charger
10 Fault when charging
11 Tips and Tricks
12 Maintenance
17026903_0409 PowerCutter.book Seite 14 Dienstag, 14. April 2009 1:33 13
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Metabo PowerCutter Li bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Metabo PowerCutter Li in de taal/talen: Alle talen als bijlage per email.

De handleiding is 6,97 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info