625666
13
Verklein
Vergroot
Pagina terug
1/96
Pagina verder
ENGLISH
13
ENG
Pull out the mains plug immediately if the battery
charger starts to smoke or flames emerge!
See page 3 (please unfold).
PowerCutter...:
1Enclosure
2Handle
3 Battery pack release
4 Battery pack
5 Trigger switch
6 Switch lock (against accidental activation)
7 Hand protection
8 Hexagon spanner
9 Screw with Belleville spring (for securing
cutting blade)
10 Cutting blades
11 Upper cutting blade
12 Bearing
Battery charger LC 60:
13 C
harging compartment
14 W
arning display
15 O
peration display
Battery charger LC 60:
Automatic balancing of the individual battery
cells permits optimum utilisation of the available
capacity and, at the same time, lengthens the
service life of the battery pack.
PowerCutter...:
Check Quick stop:
Switch machine on briefly and then off again. Have
the machine repaired if braking time is clearly
lengthened.
Charge the battery pack before use (4).
Battery charger LC 60:
Before plugging in, check to see that the
rated mains voltage and mains frequency, as
specified on the rating label, match your power
supply.
Self-test
Insert the mains plug. The warning display (14) and
the operating display (15) light up in succession for
approx. 1 second.
8.1 Battery pack
Removing battery pack:
Press the battery pack release (3) and remove
the battery pack (4).
Inserting battery pack:
Push in battery pack (4) until it engages.
8.2 Switching On and Off
Switching on
(safety operation):
Push the switch lock (6) in the direction of the
arrow and press the trigger switch (5).
To switch off:
Release the actuated trigger switch (5).
Thanks to the patented Quick stop, the cutting
blades come to a standstill within approx. 0.3
seconds.
Have the machine repaired if braking time is
clearly lengthened.
The noise that sometimes occurs during a
machine Quick stop is design-related and has no
influence on operation and service life.
8.3 Replacing cutting blades
Replace cutting blades (10) (or turn then over) if
they are blunt or damaged.
Never check the sharpness of the cutting
blades with your fingers. The cutting blades
are blunt if the cut twigs or leaves are chapped or
frayed.
Remove the battery pack (4) from the
machine to prevent accidental activation.
Danger of injury from the sharp edges of the
blades. Do not touch the cutting blade (10)
and upper cutting blade (11). Wear protective
gloves.
See illustration (A), page 3.
1 Remove battery pack
(4)
.
2 Remove enclosure (1) from cutting blade.
3
Block the cutting blade (10)
with a sufficiently
long wooden rod (or non-ferrous metal rod)
to prevent rotation (do not block or hold
with your fingers or hand).
4 Remove screw with Belleville spring (9)
using a hexagon spanner (8) by turning
counterclockwise (right-hand thread).
5 Remove wooden rod (or non-ferrous metal
rod).
6
Carefully remove the cutting blade (10)
.
Cutting blades (10)
ground on both sides
5Overview
6 Special Product Features
7 Commissioning
8 Use of PowerCutter...
17026903_0409 PowerCutter.book Seite 13 Dienstag, 14. April 2009 1:33 13
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Metabo PowerCutter Li bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Metabo PowerCutter Li in de taal/talen: Alle talen als bijlage per email.

De handleiding is 6,97 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info