476833
6
Verklein
Vergroot
Pagina terug
1/38
Pagina verder
6
13
12
11
- Power Supply
Connect chain saw to correct voltage, that is, be sure
that the voltage supplied is the same as that specified
on the nameplate of the tool (11).
- Replacement Parts
When servicing, use only identical replacement parts (11).
- Polarized Plugs
To reduce the risk of electric shock, this equipment has
a polarized plug (one blade is wider than the other). This
plug will fit in a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician to install the
proper outlet. Do not change the plug in any way.
- Wear ear protectors during operation.
- Before making a felling cut, remove dirt, stones,
loose bark, nails, staples and wire from the tree.
- Secure the log so that it will not rol or move suddenly
during operation.
- AVOlD UNINTENTIONAL STARTING. Dont carry
plugged-in tool with finger on switch. Be sure switch
is OFF when plugging in.
- Attention! Do not expose this tool to rain (12) and
pull plug immediately if the supply cable is damaged
or cut (13).
- The chain saw must not be left outdoors during rain
and it must not be used when wet.
VOLTAGE WARNING:
Before connecting the tool to a power source
(receptacle outlet, etc.) be sure the voltage supplied is
the same as that specified on the nameplate of the tool.
A power source with voltage greater than that specified
for the tool can result in SERIOUS INJURY to the user -
as well as damage to the tool. If in doubt, DO NOT
PLUG IN THE TOOL. Using a power source with voltage
less than the nameplate rating is harmful to the motor.
Use of Extension Cord
If the extension cord is intended to be used outdoors, the
cord shall be marked with the suffix W-A following the cord
type designation, for example - SJTW-A, to indicate it is
acceptable for outdoor use. Use an extension cord heavy
enough to carry the current the tool will draw. Undersize
cord will cause a drop in line voltage resulting in loss of
power and over-heating. Make sure the extension cord is in
good condition before using. Keep the cord away from the
cutting area and to position cord so that it will not be caught
on branches, and the like, during cutting. Use the table below
to determine the proper wire size required in the extension
cord.
Contact MAKITA Authorized or Factory Service Center if a
proper extension cord cannot be found.
SAVE THESE INSTRUCTIONS !
Nameplate UC 4000
Ampere rating 0-5.0 5.1-10.0 10.1-13.0 13.1-15.0
(on nameplate)
Ext. Cord Length Wire Size (American Wire Gauge)
25 Ft. 18 18 16 14
50 Ft. 18 16 16 14
75 Ft. 18 16 14 14
100 Ft. 16 14 12 12
125 Ft. 16 12 12 12
150 Ft. 16 12 12 -
2600FPM(800m/min)
Hamburg
Germany
50-60Hz
UC 4000
120V~
13 A
No.
16" (400mm) Chain Saw
442.040.661
980.114.450
96070000
Class 2C. CSA Z 62.1, Z 62.3
528.091.056
®
®
LISTED
82Z2
C
Indicate when ordering spare parts!
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Makita UC 4000A bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Makita UC 4000A in de taal/talen: Engels, Frans als bijlage per email.

De handleiding is 2,86 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Makita UC 4000A

Makita UC 4000A Gebruiksaanwijzing - Deutsch - 20 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info