522384
4
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
Reassembly: Before you begin reassembly of the watermaker, clean all parts using clean, lint-free rags. At this
time, all parts should be carefully inspected for wear or damage. Use a 10x magnifier or loupe to examine the
seals, o-rings and other small parts. Stubborn rust stains and other deposits on metal parts can be cleaned with
a soft-metal wire brush (e.g., stainless steel or brass). Do not use polishes, cleaning compounds containing
abrasive materials, or regular steel wire brushes. During reassembly, refer to Figures A-3 and A-4 in the
Appendix for full-size drawings and identification of the components included in the Repair Seal Kit.
In the following procedure for reassembling the watermaker, it is assumed that all parts have been cleaned and
that all o-rings, seals, and mating surfaces have been lightly lubricated with non-petroleum silicon grease
(supplied with the Repair Seal Kit). References to the Repair Seal Kit will be abbreviated to “RSK.”
Warning: Use only non-petroleum silicon grease to lubricate your watermaker. Lubricants with a petroleum
base will damage several watermaker components, including the reverse osmosis membrane. Be especially
cautious of lubricants that contain” teflon, silicon, etc.such products could also contain petroleum-based
components. An ample supply of silicon grease is included with each RSK.
1. Make a note of the correct orientation of the old cup ring and PIP seal and then remove them from the
piston assembly. Since these components are made of rather stiff rubber, it is usually easier to cut them off.
Use a small screwdriver to wedge under the cup seal and pry it up. While holding it up, cut it with a small
pair of scissors. Repeat this process for the PIP ring.
Reinstall the piston: If you want to replace the O-rings on
the piston, refer to the figure below
o Install washer with chamfer on washer facing ½”
dia of plunger rod and a new O-ring onto the
plunger rod, if you have an old-style piston, you
only have to install a new O-ring into the plunger
rod without a washer.
o Slide piston onto the threaded end of the plunger
rod, and secure with the washer and nut.
2. Refer to Figure R-6 during the following procedure. Place the
piston assembly on a flat, stable surface with the shaft pointing
up. Slide the installation tool (provided in the RSK) over the
piston shaft with the wide end down. Lubricate the new PIP ring,
cup seal and the installation tool with
silicon grease. With the grooved side
facing up, slide the PIP ring down the
installation tool and onto the piston.
Repeat this process for the cup seal. Note
that the grooved side of the cup seal
should be facing down; i.e., the grooved
sides of the PIP ring and the cup seal
should be facing each other. When
finished with the installation, remove the
installation tool from the piston shaft.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Katadyn REPAIR SEAL KIT PowerSurvivor 40E bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Katadyn REPAIR SEAL KIT PowerSurvivor 40E in de taal/talen: Engels als bijlage per email.

De handleiding is 0,53 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info