522384
2
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
Disassembly:
1. Before beginning disassembly, run the watermaker and stop it when the piston shaft is at its farthest point
of travel away from the pump (i.e., toward the drive assembly). This provides enough room for sliding the
rubber boot toward the pump in Step
3.
2. Disconnect the pump from the drive
assembly by first removing the two
hex nuts and 5" sockethead cap-
screws from the check valve plate, us-
ing the 1/2" open-end wrench and
1/4" allen wrench. Also remove the
two hex nuts securing the pump back
plate to the drive assembly. See Fig-
ure R-1.
3. Slide the black rubber boot on the
piston shaft toward the pump to
expose the drive shaft coupling pin.
Use a small allen wrench or similar
tool to push the coupling pin out of the drive shaft (see Figure 6). Be aware that the coupling pin fits loosely
in the drive shaft and may fall out when the rubber boot is removed. Be careful not to lose it. Separate the
drive assembly from the pump and set the drive assembly aside.
4. Remove the two 3" socket-head
capscrews using a 1/4" allen wrench.
Separate the pump back plate and
piston assembly from the pump body
(see Figure R-2).
5. If the piston assembly remained with
the pump back plate when it was
removed, pull the piston out of the
back plate and set it aside. If the
piston stayed in the main pump body,
pull it out of the cylinder. If the piston
assembly is difficult to remove from
the pump body, insert a small allen
wrench or Phillips screwdriver
through the coupling pin hole. This
will provide a “t-handle” with a better
grip for extracting the piston
assembly. Be aware not to damage
the surface of the piston shaft.
6. Remove the large o-ring (8012588) from its groove in the side of
the pump back plate that faces the pump body. Remove the wiper
block and spacer (if present) from the pump back plate. Use
needle-nosed pliers to pull the old wiper block seal out of the
wiper block. See Figure R-3. (Note: This seal is usually damaged
during removal. Be sure you have a replacement on hand before
removing it.)
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Katadyn REPAIR SEAL KIT PowerSurvivor 40E bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Katadyn REPAIR SEAL KIT PowerSurvivor 40E in de taal/talen: Engels als bijlage per email.

De handleiding is 0,53 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info