522384
3
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
7. From the side of the pump back plate that contained the large o-ring, insert a round drift of slightly smaller
diameter than the hole for the piston shaft. (Note: a small socket on an extension or a wooden dowel
makes a suitable drift). Tap the drift with a mallet to drive the two backup washers, two piston shaft seals
and the piston shaft bushing out of the pump back body. See Figure R-4.
8. Remove the remaining two 3/4" sockethead capscrews from the check valve plate using a 1/4" allen
wrench. Separate the check valve plate from the pump body.
If it is difficult to remove, try rotating the check valve plate
90°. This provides a better grip for pulling the check valve
plate from the pump body.
9. After the check valve plate has been separated from the
pump body, the membrane tube plug will remain in either the
check valve plate or the pump end of the membrane housing.
Use one of the following procedures to remove it:
A. If the membrane tube plug remains in the mem-
brane housing, insert a hard, thin edge (e.g., a dull
pocket knife) between the tube plug and the fiberglass
molding of the membrane housing. Work the blade
sideways to pry the tube plug out slightly, until there is enough of a gap between the tube plug body
and the membrane housing to insert a flat blade screwdriver. Then use two screwdrivers on opposite
sides of the tube plug to carefully work it out of the membrane housing. Avoid gouging or damaging
the membrane housing or the tube plug.
B. If the membrane tube plug remains in the check valve plate, use a thin edge and/or flat blade
screwdrivers, on opposite sides of the membrane tube plug, to carefully pry the plug out of the check
valve plate. Avoid damaging the membrane tube plug.
10. Disassemble the valves in the check valve
plate (see Figure R-5.) Use a 5/8" open end
wrench to unscrew the intake valve seat.
Remove the intake poppet valve and its
spring. If necessary, use needle-nosed pliers
to remove the poppet valve retainer. Then use
the pliers to lift out the reject poppet valve
and its seat. Grip the x-shaped ribs of the
reject poppet valve and pull straight up. The
seat will be pulled out along with the valve.
After the reject poppet valve and its seat have
been removed, retrieve the reject poppet
valve spring from the bottom of the check
valve plate cavity.
This completes the disassembly of all user-
serviceable parts of the Katadyn PowerSurvivor
40E watermaker.
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Katadyn REPAIR SEAL KIT PowerSurvivor 40E bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Katadyn REPAIR SEAL KIT PowerSurvivor 40E in de taal/talen: Engels als bijlage per email.

De handleiding is 0,53 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info