555058
9
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
The JA-80Y GSM communicator - 9 - MFJ55304
The telephone numbers M1 and M8 will also receive the GSM
provider’s replay.
If only uu..u follows the CREDIT instruction (no xx yyy zz) then
periodic balance checking will not be performed, but the balance will
be checked immediately and the uu..u checking instruction will be
memorized, so that in future it will be possible to check the balance
just by sending the instruction code CREDIT.
Example: sending the SMS instruction “code credit
101# 7 50 1
causes the credit balance to be checked every 7
th
day (after the SMS
has been sent) and if the balance (starting with the first character in
the message from the GSM provider) is lower than 50 currency units it
will be reported.
Warning:
the use of prepaid cards in the communicator is risky.
Some GSM providers block cards with enough credit but which are not
topped up frequently enough. We strongly
advise the use of tariffed
SIM cards !!!
5.18. Remote programming by the SMS instruction
Instruction PRG can be used to send programming and operating
sequences to the alarm system:
code_PRG_seq,seq,seq...
where:
code is valid access or service code (e.g. 8080 or 1234)
_ space
seq programming sequence usually set via the keypad
Note:
In the sequence can be used characters 0 to 9, and #)
When the valid instruction is received, communicator simulates
entering the keys on the keypad, comma in the SMS is taken as a
pause in the sequence entering
System must be unset and switched to the service mode
The number of sequences in one SMS is limited by the maximum size of
the SMS in the GSM network.
Example: by sending SMS 8080 PRG
08080,201,# the exit delay will
be set to 10s
5.19. Registration code for www.GSMLink.cz
If remote access via the Internet is desired, then the system has to be
registered on the web page: www.GSMLink.cz
Each communicator has its own unique registration code, which is
printed on the label attached to the communicator module. This code
can also be sent by SMS to your mobile phone by the keypad entry:
910 xx...x 0 where xx...x is the tel. number to send the code to
Notes:
It takes a certain time to receive the registration code (depends on
the current traffic in the network)
The registration code has the format: xxxxx-xxxxx-xxxx
5.20. Triggering re-registration to the GSM network
After 923 has been entered, the communicator quits the GSM network and
then re-registers itself. This re-registration does not change any settings in
the communicator. It should be used after GSM network faults or data
collisions and in some networks it also has to be used after a blocked SIM
card has been unblocked by the GSM provider.
It is also possible (if the SIM card can still receive) to trigger GSM network
re-registration by sending the SMS instruction: code GSM (code =
master, user or service code).
5.21. Communicator reset
Entering 98080 returns the communicator to its factory default settings and
texts, erases all telephone numbers and disables reporting. The text will
not be changed.
5.22. Memorizing the SIM card’s PIN code in the communicator
It is recommended to use a SIM card with disabled PIN protection. If it is
impossible to disable the PIN, then it can still be used by entering the
following sequence (it must be entered after the control panel has been
powered up).
920 PIN 0
Example: if the SIM card PIN is 1234 enter 92012340
Notes:
If the communicator does not register to the GSM network within
1 minute of the PIN being entered (this problem is shown by red
LED flashes), then you either entered a wrong PIN or the GSM
signal is too weak. In such a case:
o enter 9200 while in service mode (erases the entered PIN)
o disconnect the control panel power (mains and battery)
o take out the SIM card and try it in a mobile phone (it should
register to a GSM network when located at the control panel)
o if you know the right PIN code and there is a GSM signal
strong enough, put the SIM card back into the communicator,
turn on the control panel power and then enter the PIN code
(920 PIN 0) – the communicator should then register to the
GSM network (its red LED should turn off within a minute)
The communicator memorizes the PIN and it will use it
automatically whenever it registers to the GSM network.
If you are replacing the SIM card in the communicator with
another one and the former one used a PIN code, first switch the
control panel to service mode and enter 9200 to erase the
former PIN code. The SIM card can then be changed.
Note: The PIN code cannot be changed if the ARC settings are locked
Factory default setting: The PIN code is erased
5.23. GPRS log-in parameters
GPRS data communication (wireless Internet via a GSM network) is
used for remote access via the Internet and also for IP reporting to the
ARC. To use GPRS data it must first be enabled (activated) in the SIM
card (contact your GSM provider for details). Then the GSM network’s
GPRS parameters must be programmed by sending the following SMS
instruction to the communicator.
code_GPRS_ x..x,y..y,z..z
where:
code is a valid (master, user or service) access code (e.g.
8080 or 1234)
_ space
x..x APN (Access Point Name)
, comma
y..y username (do not enter if not required)
z..z password (do not enter if not required)
Notes:
Most public GSM networks only request an APN (do not enter y..y
and z..z parameters in this case)
The GPRS parameters can only be programmed if the system is in
service mode and the ARC settings are not locked
Factory default setting: APN = Internet
5.24. ARC phone numbers / IP addresses
Events can be reported to up to 2 ARCs (which can be independent or
ARC2 can work as ARC1’s backup). Each ARC can have its main and
backup phone numbers (or IP addresses) programmed with:
Main: 01 a xx....x 0
Backup: 02 a xx....x 0
where:
a 1=ARC1, 2=ARC2
xxx...x tel. number (max. 20 digits)
or IP address and port – entry format example:
01 2 8 192 168 001 123 08080 0
where 8 (auto-converts to #) signifies an IP address
which must have 12 digits and must be followed by the 5
digits of the port number (no separators)
To erase a tel. number / IP address enter: 01p0 or 02p0
If numbers / IP addresses are erased there will be no reporting to that
particular ARC
Note: the communicator first tries to send data to the main number /
address, if it is not successful it tries the backup.
Factory default setting: all tel. numbers / IP addresses erased
5.25. Installation (alarm system) ID for ARC use
The installation’s ID number which is sent to an ARC with every report
can be programmed with:
03 a zz..z 0
where:
a 1=ARC1, 2=ARC2
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron JA-80Y bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron JA-80Y in de taal/talen: Engels als bijlage per email.

De handleiding is 0,17 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Jablotron JA-80Y

Jablotron JA-80Y Gebruiksaanwijzing - English - 16 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info