554835
19
Verklein
Vergroot
Pagina terug
1/22
Pagina verder
Installation manual: Oasis security system JA-80K - 19 - MKE51801
B in an unsplit system: hot key for setting sections A and
B (e.g. partial night-setting of the garage and the ground
floor).
in a split system: hot key for setting section B (C is only
set if both sections A and B are set)
? Display of triggered detectors (e.g. open windows), fault
details and PGX / PGY status.
turning on the PGX output from the keypad (the same
effect as 81)
turning off the PGX output from the keypad (the same
effect as 80)
Notes:
The A and B keys only have a function if partial setting or
splitting are enabled.
The keys
and only control the PGX output if they have
been programmed for it, see 12.5.
13.1.5. Functions beginning with the key
The following functions are available to the user via the
keypad:
1 sets the entire system (the same as key ABC)*
2 sets section A (the same as key A)*
3 sets A and B, or just B (the same as key B)*
4 event memory recall (key 4 scrolls backwards) – the
control panel records max. 255 of the latest events
5 new Master Code/Card (5 MC NC NC)
6 access code/card programming (6 MC nn NC)
7 for operation while under duress (should be entered
before the access code to secretly signal distress)
8 PGX control (ON/OFF = 81/80 or enter 8 to trigger if a
pulsed switching reaction is programmed)*
9 PGY control (ON/OFF = 91/90 or enter 9 to trigger if a
pulsed switching reaction is programmed)*
0 To enter Service Mode (0 SC – factory default 8080) or
to enter maintenance mode (0 MC – factory default
1234)
The functions allow the system to be operated from a mobile phone
keypad (if the control panel is equipped with the relevant
communicator).
13.2. Programming access codes and cards
The system can be controlled by 4-digit codes or by access
cards, of the types PC-01 and PC-02 (EM UNIQUE 125kHz
standard).
The control panel has 1 service, 1 master and 50 user codes.
Only a numerical code can be used as a service code (factory
default 8080) – see the control panel programming section.
The master code can be a numerical code (factory default
1234) or an access card. Using this master code/card, other
users’ codes and cards can be programmed or erased. The
master code/card is usually used by the system administrator.
Each user from 01 to 50 can have a numerical code, or a
card, or both (factory default: all user codes and cards from 01
to 50 are erased).
If a user has both a code and a card, then it is possible to
program whether both a code and card must be presented to
the system for system access, or whether only one of them is
required (see 12.37).
The system does not allow the same code or card to be
programmed to multiple users. (if it is desired to move a
code/card to another user, the card/code has to be erased
from its current user first).
It is possible to display which code/card positions are already
occupied in maintenance mode (see 13.4.1).
The most convenient way to program codes and cards is by
using a PC running Comlink software.
The control panel allows a maximum of 10 unsuccessful
attempts in a row to enter a valid code or card. If exceeded, a
tamper alarm starts.
13.2.1. Programming access codes and cards
Abbreviation Name Number Sequence Notes
SC Service
1
5 NC NC
Only programmable in Service Mode.
NC = new code (must be entered twice) – a card cannot be used.
Factory-default service code: 8080
This code can be changed but not erased.
Example: 5 4567 4567
MC Master
1
5 MC NC NC
Only programmable if the system is totally unset (disarmed)
MC = master code or card (factory default 1234)
NC = new code or card entry – a numerical code has to be entered twice, but a
card only presented once
Either a code or a card can be programmed as a master code (to have both is
impossible).
The Master Code can be changed but not erased.
The Master Code’s reaction is set/unset and it is assigned to all sections.
To reset the Master Code to the factory default 1234, enter 291 in Service Mode
(this will only affect the Master Code).
To make handing over the system to the end user easier, we recommend
programming the system card (provided with the control panel) to the master
code.
Example:
5 1234 and then presenting the card to the keypad’s RFID reader
UC User
50
6 MC nn NC
Only programmable if the system is totally unset
MC = Master Code or card.
nn = user code or card position from 01 to 50.
NC = new code or card entry.
Factory default: all user codes and cards are erased.
Each user position can have both a card and a code programmed to it (by using
the sequence 6 MC nn NC twice)
Each user code can have its own reaction programmed by an installer in Service
Mode, and with a split system, codes can be assigned to different sections.
Example:
6 1234 12 4345 (code 4345 will be programmed to user position 12)
To erase codes/cards enter:
6 MC nn 0000 erases the code and the card in user position nn.
6 MC 00 UC erases the code UC (or card UC) if programmed to any user position.
6 MC 00 0000 erases all user codes and cards in user positions 01 to 50.
19

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron JA-80K bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron JA-80K in de taal/talen: Engels als bijlage per email.

De handleiding is 0,55 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Jablotron JA-80K

Jablotron JA-80K Gebruiksaanwijzing - English - 1 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info