554882
3
Verklein
Vergroot
Pagina terug
1/15
Pagina verder
GD-04 DAVID 3 MKS51202_OS1*
5. Insert the circuit board back to its position.
6. Do the wiring, see below.
4. Wiring
1. Power supply – use the +12V and GND terminals. Any
power supply adapter used should provide 12V DC
voltage and up to 500mA of current. If an LT-89 mains
adapter is used (a recommended option) wire the grey
marked conductor to GND. Do not turn the power supply
on until all input/output wiring has been done.
2. Output relay contacts – available
at the X1+X2 and Y1+Y2 terminals.
Each contact is fused to 5A. The
circuits which the contacts belong to
are protected from the remaining
electronics by a safety separator
and are capable of switching up to
5A at 250V AC. The following
example shows a light bulb control via the Y output relay:
3. Input terminals – marked A to D. The terminals respond to a
connection or disconnection to or from GND by sending an SMS
report. No external voltage supply can be connected to these
terminals – they can only be controlled via a potential-free
switch/contact. Example of wiring a switch to input A:
5. Initial powering up
4. Turn the power supply on, registering to the GSM network is indicated by the LED
flashing (if no indication occurs, check the power supply wiring).
5. After GSM registration the LED stops flashing (usually within 1 minute). Continued
flashing indicates a GSM registration fault. Disconnect the power supply and check that a
valid SIM card has been correctly installed into the device, see 2 and 3).
6. Send the SMS instruction STATUS to David’s SIM card number.
7. David responds by a status report, e.g. STATUS: A0,B0,C0,D0,X0,Y0,GSM:80% (which
means that all A to D inputs and both the X and Y relays are switched off and that the GSM
signal strength is 80%). Depending on the GSM network traffic the response may take some
time. If no response occurs, verify that “STATUSis spelt exactly right in the text of the
message and that you are sending the message to David’s correct SIM card number (repeat
the previous step).
6. Programming
6.1. Via the Internet
The simplest way to program David is via the web site www.david.jablotron.cz.
You fill in all the required parameters in a form on a single web page, press the Send button,
and the Jablotron web server will forward the settings to your David via the GSM network.
Performance of a successful transfer is confirmed from David by an SMS reply "PROGRAM OK"
to your mobile phone.
Switch
12V DC
power supply
( adapter)LT-89
_
+
230V/50Hz
Light bulb
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron GD-04 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron GD-04 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,26 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info