555042
4
Verklein
Vergroot
Pagina terug
1/5
Pagina verder
GSM pager CA-1802 „Athos“ 4/5 MHF57402
SMS from an internet gateway which adds more text
advertisements etc. When using the % character it is always
necessary to insert the Master or User code followed by a space
before the command itself.
SMS instructions can be renamed. Example: It is possible to replace
“IMO“ by “BLOCK“.
The parameters in bold are factory defaults.
8.1. Phone calls by handsfree set (HF-03)
If the HF-03 hands free set is installed, it is possible to receive calls
and to dial pre-programmed phone numbers DIAL x. When the ignition
key is on, an RC-8x allows you to operate the hands free set. A voltage
of +12V is required on the ignition key input when a call starts or ends.
The call is done via the car alarm’s SIM, the handsfree set is not usable
for other phones.
Incoming calls – to answer them, press any button on the RC-8x
remote control. By pressing any button again, the call will be terminated.
Calls can be automatically answered, see the HF instruction manual.
Outgoing calls – when the ignition key is on (i.e. when a voltage of
+12V is present on its input), the RC-8x allows you to call up to 4 pre-
programmed numbers (see the configuration table).
If the ignition key is off (i.e. no voltage of +12V is present on its input),
all incoming calls are automatically rejected. If the car is immobilized all
calls are automatically answered (it is possible to listen in).
8.2. Alarm
When an alarm is triggered, the siren output will be switched on for 30
sec., warning SMS messages will be sent to all phones (TEL1 to TEL4).
Subsequently, these phones will also be called by the GSM pager. If
automatic location is turned on, a request for location detection is sent.
The LED indicates the alarm for 2 minutes. To activate inputs
subsequently, an interval of at least two minutes is required.
To stop the alarm, disarm the alarm by pressing the
button on the
remote control.
Example of an alarm SMS:
Your car reports: Alarm, INP activation, Time 10.12.04 01:45
9. Editing SMS texts
The SMS texts (alarm information and instructions) are factory pre-
programmed. However, it is possible to change these texts using a
mobile phone or via the www.GSMLink.cz
internet page. This makes
communication convenient for the user.
To change text by mobile phone, send an SMS as below. A single
SMS enables you to specify changes to several texts. Terminate each
text with a comma:
MASTER TXT zz,text,zz,text,…
where: zz is the text index (see following table)
text is your new text – up to 30 characters, full stop (dot) or
comma cannot be used in the text, spaces are allowed
Example: MASTER TXT 03,BLOCK PLEASE
Text numbers 01 to 26 are instructions requiring a MASTER code for
their modification. If you modify these texts, you change the instructions
which the GSM pager will respond to. For example, replacing “STATUS”
with “STATE PASSWORD” will cause state detection to be only
obtainable by “STATE PASSWORD”. This way you can insert a
“password” into the texts which prevents misuse. All other texts are of
informational character and correspond to particular events, states and
input names. This allows you to adjust the names to a form which suits
you well. For example, “INP 1” can be replaced with “bonnet” etc. Texts
can be replaced using the MASTER code as well as the USER code
(optional).
A convenient way for text modification is to use the GSMLink web
page.
SMS text table
Zz Factory default text zz Factory default text
SMS commands: 48 Telephone 4
01 AM 49 Telephone - UC
02 DM 50 Telephone - MC
03 IMO 51 Wireless detector 1
04 UNIMO 52 Wireless detector 2
05 STATUS 53 Wireless detector 3
06 HELP 54 Wireless detector 4
07 CREDIT 55 Wireless detector 5
08 DIAL 56 Wireless detector 6
09 HF 57 Wireless detector 7
10 LOCATOR 58 Wireless detector 8
11 MC 59 Wireless controller 1
12 UC 60 Wireless controller 2
13 DIP 61 Wireless controller 3
14 TEL 62 Wireless controller 4
15 LEARN Status information:
16 SIREN 64 Car alarm reports
17 SET 65 Status:
18 AUXA 66 Armed
19 AUXB 67 Disarmed
25 ON 68 Ignition key ON
26 OFF 69 Ignition key OFF
Events: 70 Engine is blocked
30 Alarm 71 Engine is unblocked
31 Alarm cancelled by a user 72 No alarm
32 Fire alarm 73 Alarm timeout
33 Tamper alarm 74 Low battery voltage
34 Disarming 75 Power failure
35 Arming 76 Power recovery
36 Low battery voltage 77 Time
37 Engine is blocked 79 Partially
38 Engine is unblocked Confirmation SMS:
Source:
81 Command accepted
40 Ignition key 82 Command syntax error
41 Door contact 83 New MC code:
42 INP1 activation 84 New UC code:
43 INP2 activation 85 Reset
44 Low battery voltage sensor 86 Registered phone number:
45 Telephone 1 87 Credit:
46 Telephone 2 88 LEARN mode, enrolled
47 Telephone 3
The grey-tinted items are not available for RESET 3 mode. Use only
ASCII character set during the text editing.
10. Internet remote access
The web site www.GSMLink.cz enables remote control (to users) and
setting (to installers) of the GSM pager.
To get internet access to an installed and powered car alarm you will
first be asked to register your car alarm on the first page. You will find a
unique registration code for your car alarm on the warranty card.
11. Central monitoring station communication
The GSM communicator allows central monitoring via GPRS data
protocol. The central monitoring station (CMS) gets arming, disarming and
alarm information. It also regularly checks the communication link to the car
after it is armed. So if anyone tries to tamper with GSM communications, it
will indicate an alarm at the CMS.
12. Additional features
12.1. Remote siren activation
You can operate the siren remotely by the SIREN instructions. These
instructions are accepted from all authorized (stored) phone numbers.
Commands are also accepted from any unknown phone number if they start
with the USER code.
Instruction Status
SIREN ON activates SIR output permanently
SIREN OFF deactivate SIR output
SIREN activates SIR output for 30 sec.
SIREN xxM
or
SIREN xxxS
xxM – is the numeric value of the
duration of SIR output activation, in
minutes
xxxS – as above, but in seconds.
LED indicator signals
LED state Meaning
OFF Disarmed
permanently ON Connecting to a GSM network or a phone call
Regular fast flashing
Alarm or an alarm memory or learn mode
Interrupted light Car was stopped (immobilization)
Flashing after ignition off GSM network is not available
Flashes after ignition on Number of enrolled remote controls
12.2. Pre-paid SIM card balance
It is recommended not to use prepaid cards in the car alarm. If you
have no other choice than prepaid cards, you can enable the CREDIT
instruction by the following sequence:
MASTER CREDIT uuu..u xx yyy zz
where: uuu…u is the provider’s code to obtain the balance
xx is the time period (in days) for regular checking
yyy is the threshold level below which the balance is
reported to the user (TEL1)
zz is the position of the first digit of the balance in the reply
SMS from the provider
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron CA-1802 - Athos GSM RESET 3 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron CA-1802 - Athos GSM RESET 3 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,23 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Jablotron CA-1802 - Athos GSM RESET 3

Jablotron CA-1802 - Athos GSM RESET 3 Gebruiksaanwijzing - English - 16 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info