555035
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
GSM car alarm CA-1202 „Athos“ 2/4 MHF52604
Figure 1: installation of the car alarm in Mode 2
6.1 Programming sequences
Enter the prescribed spaces in SMS texts as shown in the table below. MASTER is a factory default master code, which should be changed to your own
password. All SMS texts are case insensitive.
SIM entry* Text of SMS instruction Description
RESET 2 MASTER RESET EN 2 Mode setting. Factory default is 0 – no function (immobilization relay copies ignition). Note: By
performing the RESET EN x instruction, all settings, remote controllers and enrolled wireless detectors
will be erased! RESET is indicated by four siren chirps.
Not possible MASTER UC uuuu
User Code setting – the code (password) allows you to operate the alarm remotely via SMS from
unauthorized phones. uuuu is a new user code, up to 8 characters (A –Z & 0 – 9). Factory default
user code is USER
Not possible MASTER MC xxxx Master Code setting, xxxx is a new master code, up to 8 letters (A –Z & 0 – 9).
The code allows you to change settings for the car alarm. Factory default master code is MASTER
TEL1 xx...x MASTER TEL1 xx...x
TEL2 xx...x MASTER TEL2 xx...x
TEL3 xx...x MASTER TEL3 xx...x
TEL4 xx...x MASTER TEL4 xx...x
Setting of phone numbers to report alarms (these phones will also be authorized to control the
alarm via SMS without a user password)
E.g.: MASTER TEL2 +420602123456 will enter the phone number to TEL2 memory
MASTER TEL3 0 will erase the TEL3 memory.
DIAL1 xx...x MASTER DIAL1 xx...x
DIAL2 xx...x MASTER DIAL2 xx...x
DIALA xx...x MASTER DIALA xx...x
DIALB xx...x MASTER DIALB xx...x
Setting of phone numbers to dial using Hands free.
E.g.: MASTER DIAL2 +420602123456 will enter the number to DIAL2 memory (which is dialed after
you press button 2 on the remote control)
MASTER DIAL2 0 will erase the memory DIAL2.
DIP abcdefghij MASTER DIP abcdefghij DIP parameters entry – see part 7
SET abcdefghi MASTER SET abcdefghi SET parameters entry – see part 8
Not possible MASTER LEARN RC Remote Control enrollment - up to 4 controllers can be enrolled, turn the ignition key on before
sending the instruction. To enroll a remote control press and hold buttons A and B together for 3
seconds. After you enroll all remote controls, turn the ignition key off.
Not possible MASTER LEARN JA JA-60 wireless detector enrollment – up to 8 detectors can be enrolled, turn the ignition key on
before sending the instruction. To enroll a detector insert its battery. After you enroll all detectors, turn
the ignition key off.
Not possible
MASTER TXT 01,text Editing of SMS texts (reports and instructions), see part 10
TELU xx...x MASTER TELU xx...x Sustained call setting (for pre-paid cards) 1x month the xx..x number is called, call duration 10 s.
* See part 5 for details.
GSM car alarm CA-1202 „Athos“ 3/4 MHF52604
7 DIP parameters
By SMS: MASTER DIP ABCDEFGHIJ you can change 10 features:
Description
DIP
0 1
A 0 = Silent arming/disarming without siren chirps
1 = 10 ms siren chirps when arming/disarming (non backed-up siren)
2 = 20 ms siren chirps when arming/disarming (backed-up siren)
B Silent alarm
Audible alarm (30 sec.)
C
SMS alarm report only
SMS alarm report + siren sound
phone call
D SMS remote control not
confirmed by SMS reply
SMS remote control instructions
confirmed by SMS reply
E
0 = arming control by dialing in from TEL1 to TEL4 disabled
1 = arming control by dialing from TEL1 enabled
2 = arming control by dialing from TEL1 and TEL2 enabled
3 = arming control by dialing from TEL1, TEL2 and TEL3 enabled
4 = arming control by dialing from all TEL1 to TEL4 enabled
Arming and disarming by dialing from authorized phones is free of
charge
F
Arming control by dialing
in is not confirmed by
SMS
Arming control by dialing in (see E) is
confirmed by SMS to the phone
which dialed the car alarm
G
User can not change SMS
texts
User can change SMS texts by TXT
sequence
H
No function in mode 2 (set to 0)
I
0 = Immobilization by arming and by SMS instruction
1 = Immobilization by arming and automatically 5 minutes after ignition is
turned off and also by SMS instruction
2 = Immobilization only by SMS instruction
J
Self-location disabled
The car´s location will be sent by
SMS to all TEL1 to TEL4 if there is
an alarm or if the car stops after
immobilization SMS instruction (See
13.6.)
Factory default setting is DIP 1111000000 (bold letters in the text). If you
want to change only particular parameters, enter x for the others (i.e.
MASTER DIP 0xxxxxxxxx will make arming control silent).
8 SET parameters
By SMS: MASTER SET ABCDEFGHI you can change 9 features:
Description
SET
0 1
A
Open door arming indication
disabled
Audible indication of arming with
open door (4 beeps)
B
Voltage detector disabled
Voltage drop detector enabled
C
No function in mode 2 (set 0)
D
DOOR input logic:
0 = automatic
1 = activated by falling edge (grounding)
2 = activated by rising edge (disconnecting from GND)
E INP1 logic:
0 = automatic
1 = activated by falling edge (grounding)
2 = activated by rising edge (disconnecting from GND)
F INP2 logic:
0 = automatic
1 = activated by falling edge (grounding)
2 = activated by rising edge (disconnecting from GND)
G Input for central locking signal logic
0 = automatic
1 = activated by falling edge (grounding)
2 = activated by rising edge (+12V)
H Confirmation by the turn
lights is not required
Confirmation by the turn lights is
required
I no function in Mode2
Factory default setting SET 100000010 (bold letters in the text).
If you want to change only particular parameters, enter x for the others
(i.e. MASTER SET 0xxxxxxxx will disable open door arming indication).
9 User instructions
9.1 Remote control arming and disarming
The alarm will be armed when the car is locked remotely by the original
remote control and disarmed when the car is unlocked remotely. The locking
(according to the setting in 8 H) and unlocking must always be followed by
confirmation from the turn lights. If the car is unlocked by the key (no
confirmation from the turn lights) then the alarm will be triggered. To stop the
alarm it is necessary to unlocked remotely by the original remote control. We
do not recommend installing the car alarm in this mode to cars in which
unlocking the door by key is confirmed by the turn lights (or disable this
feature if possible).
9.2 Remote control by SMS instructions
SMS instructions sent from an authorized phone (TEL1 to TEL4) can
operate the alarm but not the central locking remotely. Factory default
instruction texts are shown in the following table. The instruction texts
can be changed by SMS text editing, see part 10.
If an SMS is sent from an unauthorized phone (other than TEL1 to
TEL4), a valid user code must be entered before the instruction (e.g.
USER AM).
SMS text Description
AM
ARM and lock the car
DM
DISARM and unlock the car
IMO
STOP (immobilize) the car (after turning the ignition key off)
UNIMO
Unblock (mobilize) the car
STATUS
The car alarm will reply with status information, e.g. „car
reports: Time: 27.01.04 13:04, Status: Armed, Unblocked,
Ignition off“.
HELP
The car alarm will reply with a brief list of SMS instructions.
UC uuuu
To change the user code. uuuu is the new user code, up to 8
characters (A –Z & 0 – 9). Factory default user code is
USER
CREDIT
To obtain the balance of a prepaid SIM card if used. See 13.7
for details
HF abcdef
Hands-free set adjustment:
a – enable calls (0= disabled, 1=enabled)
b – auto answer incoming calls (0= disabled, 1=enabled)
c – microphone sensitivity 0 to 9, (5)
d – speaker volume 0 to 9, (5)
e - ringing tone volume 0=mute to 9= max., (5)
f – ringing sound 0 to 9, (5)
LOCATOR
To obtain the car location from the GSM provider. See 13.6
for details.
The parameters in bold are factory defaults.
The instruction must contain spaces as shown in the table
Only basic ASCII can be used in the SMS instruction texts
If the SMS text contains the % sign, then the following text will be
ignored. Characters %% in the message stop processing the
following text. Using these characters is suitable when sending an
SMS from an internet gateway which ads another text –
advertisements etc. When using the % character it is always
necessary to insert the Master or User code followed by a space
before the command itself.
9.3 Dialing-in remote control
If enabled by the DIP parameters (see 7), the car alarm can be armed
and disarmed remotely by dialing in from an authorized phone (TEL1 to
TEL4). The car alarm will not answer the incoming call, but when it
recognizes your number, it will change status (Arm or Disarm).
Such remote control is free of charge since the phone is not answered.
Warning – if you dial your car alarm accidentally it can cause disarming of
the alarm.
Controlling by dialing in will result only in arming/disarming the alarm but
it will not lock/unlock the doors
Phone calls by an installed hands free set
If the optional HF-03 hands free set is installed, it is possible to receive
and make phone calls via the car alarm. When your car is disarmed and
ignition key is on, the remote control (RC-40) allows you to operate the
hands free set.
Incoming calls – to answer them, press any button on the RC-40 remote
control. By pressing any button again, the call will be terminated.
When armed, all incoming calls are automatically rejected. If the car is
blocked (by IMO instruction) all calls are automatically answered (it is
possible to listen and to speak to the car remotely). Automatic call
answering while you are driving can also be enabled by the HF
instruction (see 9.2).
To make a call – you can call up to 4 preprogrammed numbers while you
are driving. By pressing button A, B, 1 or 2 on the remote control you will
dial the corresponding number (pre programmed by DIALA to DIAL2, see
6.1)
9.4 Alarm
When an alarm is triggered, the siren will sound for 30 sec., warning SMS
messages will be sent to all phones (TEL1 to TEL4) and these phones will
also be called with the siren sound.
To stop the alarm, disarm the alarm by unlocking the doors using the
original remote control or by the disarm SMS instruction (DM).
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron CA-1202 - mode 2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron CA-1202 - mode 2 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,63 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Jablotron CA-1202 - mode 2

Jablotron CA-1202 - mode 2 Gebruiksaanwijzing - English - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info