555035
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
GSM car alarm CA-1202 „Athos“ 4/4 MHF52604
10 SMS text editing
The SMS texts (alarm information and instructions) are factory
preprogrammed. However, it is possible to change these texts by a
mobile phone or via internet access www.GSMlink.cz
To change a text by your mobile phone, send SMS:
MASTER TXT zz,text,zz,text,…
where: zz is the text index (see following table)
text is your new text – up to 30 characters, full stop (dot) or
comma cannot be used in the text, spaces are allowed
Example: MASTER TXT 01,LOCK PLEASE
By changing texts number 01 to 16, you will modify the control SMS
instructions. This allows you to customize the remote control of the car.
You can also make your own password part of the instruction to increase
the security of the mobile phone remote access.
10.1 SMS text table
zz Factory default text zz Factory default text
SMS commands: 44 Wireless detector
01 AM 45 Current detector
02 DM 46 Telephone 1
03 IMO 47 Telephone 2
04 UNIMO 48 Telephone 3
05 STATUS 49 Telephone 4
06 HELP 50 Telephone - UC
07 CREDIT 51 Telephone - MC
08 DIAL 52 Remote controller
09 HF Status information:
10 LOCATOR 60 Car alarm reports:
11 MC 61 Status:
12 UC 62 Armed
13 DIP 63 Disarmed
14 TEL 64 Ignition key ON
15 LEARN RC 65 Ignition key OFF
16 LEARN JA 66 Engine is blocked
17 SIREN 67 Engine is unblocked
18 SET 68 No alarm
Events: 69 Alarm timeout
30 Alarm 70 Low accumulator voltage
31 Alarm canceled by a user 71 Power failure
32 Fire alarm 72 Power recovery
33 Tamper alarm 73 Time:
34 Disarming 74 Low battery voltage
35 Arming Confirmation SMS:
36 Low battery voltage 80 Command accepted
37 Engine is blocked 81 Command syntax error
38 Engine is unblocked 82 New MC code:
Source: 83 New UC code:
40 Ignition key 84 Reset
41 Door contact 85 Registered phone number:
42 INP1 activation 86 Credit:
43 INP2 activation 87 LEARN mode, enrolled
11 Internet remote access
The web site www.GSMLink.cz enables car alarm remote control (to
users) and setting (to installers). The following features are enabled:
To get internet access to an installed and powered car alarm you will
first be asked to register your car alarm on the first page. You will find a
unique registration code for your car alarm on the warranty card.
11.1 Reset GSM
If you need to disconnect and then reconnect the GSM module to the
GSM network, then use the command “MASTER RESET GSM”.
This does not affect any settings and is typically used for GPRS
activation or charging up credit. This command always requires the
Master code.
12 Central monitoring station communication
The GSM pager allows central monitoring via GPRS data protocol. The
central monitoring station (CMS) gets arming, disarming and alarm
information. It also regularly checks the communication link to the car after it is
armed. So if anyone tries to tamper with GSM pager communications, it will
indicate an alarm at the CMS.
13 Additional features
13.1 Car battery low voltage reporting
The GSM pager checks the voltage of the car battery. If the voltage is too
low (10V) it will notify users via an SMS message. This avoids complete
discharging of the car battery if you forget to turn off your lights etc.
13.2 Back-up battery
The car alarm can be backed up by a BB-01 battery. Thus, the car alarm
can keep sending information when the car battery is disconnected. Back up
time is provided for several hours. The manufacturer recommends regular
BB-01 checking once a year. The battery should be replaced every two years.
Low back-up battery voltage (below 4V) is reported to the user via SMS
(change the battery in this case).
13.3 Voltage drop detector
The built-in voltage drop detector can trigger an alarm if an electrical
device in the car is turned on while the car is armed. The sensor activates
10 minutes after arming (if enabled).
13.4 Entrance delay acoustic indication
The siren can indicate arming and disarming by beeps (see DIP
parameter setting). The siren will also indicate the triggering of a wireless
detector which provides an entrance delay (by a single beep). This way
you can be reminded not to forget to disarm your car alarm after you
open the garage door etc.
13.5 Limited number of alarms
If any sensor (input) repeatedly triggers alarms then this particular input will
be bypassed automatically after the third alarm (it will remain bypassed until
the car alarm is disarmed).
13.6 Car location
If your GSM provider offers a location service, you have to activate the
LOCATOR command after installation by the following SMS sequence:
MASTER LOCATOR xx…x
where: MASTER is installers code
xx...x is provider’s sequence to obtain the position of
the car alarm SIM card (check with your GSM
provider for details)
After this sequence has been sent successfully once, the car alarm
memorizes the parameters and from this moment on you can obtain the
location of the car by just sending the instruction LOCATOR.
Note: GSM location service may not be available in some countries.
13.7 Pre-paid SIM card balance
It is recommended not to use prepaid cards in the car alarm. If you have
no other choice than prepaid cards, you can enable the CREDIT
instruction by following sequence:
MASTER CREDIT uuu..u xx yyy zz
where: uuu…u is the provider’s code to obtain the balance
xx is the time period (in days) for regular checking
yyy is the threshold level below which the balance is
reported to the user (TEL1)
zz is the position of the first digit of the balance in the reply
SMS from the provider
After this sequence has been sent once, the car alarm will check the
balance automatically every xx days and if the balance is lower than
yyy the user will be notified (TEL1)
If the CREDIT instruction is enabled in the above way, the user can
also obtain the current balance by the instruction CREDIT
To disable the automatic balance checking set the time period “xx” to 00.
13.8 Roaming
If you travel abroad and your SIM card supports roaming, the car alarm
will work there too.
13.9 Siren activation
If you are searching for a stolen car, you can operate the siren
remotely by the following SMS instructions:
MASTER SIREN turns the siren on for 10 minutes
MASTER SIREN ON siren on permanently
MASTER SIREN OFF siren off
To avoid misuse of this option, only an installer can switch the siren on.
13.10 LED indicator signals
LED state Meaning
OFF Disarmed
permanently ON Connecting to a GSM network or a phone call
Regular slow flashing Armed
Regular fast flashing Alarm memory
Interrupted light Car was stopped (immobilization)
Flashing after ignition off GSM network is not available
14 Specification
Please see Mode 3.
GSM car alarm CA-1202 „Athos“ 1/4 MHF52604
CA-1202 “Athos” installation manual
MODE 2 – for cars with an original remote control for central locking
Main features for this mode:
Remote control of the alarm system via SMS instructions as well
as by the original remote control for central locking.
Sending of alarm SMS messages to up to 4 phones.
Dialing and acoustic alarm warning to up to 4 phones.
Location tracking of the car (using the triangulation feature of the
GSM provider)
Central monitoring of the car when armed (fully supervised GPRS
protocol)
Remote immobilization of the car via SMS instruction.
Protecting a car with wired and wireless sensors (wireless sensors can
also be used to protect the garage where the car is parked).
Optional - Hands Free calling (receiving of any incoming call and
dialing up to four pre-programmed phone numbers)
Remote internet alarm access (user and installer levels) via
www.GSMLink.cz
1 Before installation
The CA-1202 should only be installed by a professional installer. The
manufacturer assumes no liability for damages caused by incorrect
installation or use of this product.
The Athos car alarm is suitable for cars with 12 V and negative grounding.
The main unit is designed for installation in the passenger cabin.
Disconnect the car battery before starting installation; study the car
owner manual first. Avoid drilling into the metal parts of the car body.
Note: Use only proper crimping tools and parts to make connections. Cut
all unused wires and insulate them properly.
The thin wire which leads directly out of the central unit is the remote
control and wireless detector antenna. The location of this wire affects the
communication range. Place the antenna on a suitable plastic surface so
that the other wires do not screen it.
2 Wiring
YELLOW – siren output (+12V / max. 1A).
GREY door switch input. It reacts to connection or disconnection
from the ground (automatically recognizes logic).
WHITE – INP1 input – to confirm locking/unlocking of the car by the
original remote control by confirmation signal from the turn lights
(flashers).
YELLOW–WHITE – INP2 alarm input – reacts to connection or
disconnection from the ground (automatically recognize logic).
BLUE – ignition key input (+12V). Be sure, that there is +12V while
the key is on and while starting.
GREEN – LED indicator – install it in a visible spot on the dashboard.
Connect the other end of this lead to the GND.
WHITE–BLACK (position 10) LockWHITE–BLUE (position 11)
Unlock” – control inputs for detecting locking and unlocking to
activate arming/disarming. They are usually connected to the outputs
of the central locking control unit.. If these are not available, the car
alarm inputs can be connected directly to the power wires of the
central locking motors. Two pairs of central locking wires are available.
For mode 2 use the wires with red shrinkable tube. Carefully push
the ends of the chosen wires into the main plastic connector. Be
careful to select the correct wires as removal from the main connector
is very difficult without the proper tool.
BLACK–GND – connect to the original grounding in the car.
RED power supply +12V connect directly to the battery. Check
that the installation is properly finished and that the GSM antenna is
connected before powering up!
ORANGE – back-up battery – connect optional battery BB-01
(Jablotron) if desired. If the BB-01 is not connected, then ground the wire.
2x BROWN – immobilization circuit (8A permanently, max. 12A /
3minutes).
Pink – not used
3 SIM card insertion
1. Make sure, that the PIN password on the SIM is disabled. You can
do this using a mobile phone (e.g. for NOKIA: MENU, SETTINGS,
SECURITY SETTINGS, PIN CODE REQUEST, OFF). If your SIM card
does not allow switching the PIN off, change the PIN to 0000.
2. Activate the SIM card if necessary (see provider’s instructions),
ensure that it works (by a mobile phone) and record its phone number.
3. Using a thin pointed tool, press the colored button to release the SIM
cardholder. Insert the SIM card into the holder with the gold contacts
facing up and then reinsert the holder.
4 GSM antenna installation
DO NOT switch the power on before the GSM antenna is connected.
The provided antenna is adhesive and should be attached to the car window.
The antenna should not be obstructed by any metal part. It is recommend to
install the antenna in a place where it is not easily visible (tinted part of the
window, behind the mirror etc.). If the car has an original GSM antenna installed, it
can be used (if the connector is different, use an appropriate adapter).
5 Initial powering-up of the alarm
Make sure, that the GSM antenna is connected, SIM card inserted and the
wire harness installed properly. Then connect the power (car battery). The
LED indicator will turn on and the siren will make a short chirp. Wait until the
LED turns off (up to 1 minute).
If the LED starts to flash, no GSM network was found. In such a case turn the
power off, remove the SIM card and try to use it in a mobile phone (at the
place where the GSM antenna is). Check also if the PIN protection is OFF (or
set to 0000). If the SIM card logs into network successfully, reinsert it in to the
alarm and repeat powering-up.
After the alarm is powered, you have to:
a) Select Mode 2 by command RESET EN 2
b) Enroll remote controls and wireless detectors (if used)
c) Set the programmable features (phone numbers, DIP, SET, etc.).
These can be done by:
SMS instructions – see table 6.1. For example sending SMS: MASTER
RESET EN 2 to the car alarm will select Mode 2.
Internet page: www.GSMlink.cz
is the most convenient way. To
register there you need to know the registration code (printed on the
warranty card) and the master code (factory default is MASTER).
SIM Card phone directory editing (see table 6.1 for list of features
which can be programmed this way). After the initial powering-up a list of
parameters is created in the SIM card phone directory. If you then insert
the SIM card in to a mobile phone, you can set particular features (by
entering numbers to the created list). The entry for Mode setting is not
automatically created, but it is possible to make a new entry name:
RESET EN and number: 2. Data entered this way are read by the car
alarm after the SIM card is reinserted. For security reasons it is erased
after reading.
6 Enrollment of remote controls and detectors
Up to 4 RC-40 remote controllers and up to 8 JA-60 wireless detectors can be
enrolled to the car alarm (after Mode 2 is selected by the RESET EN 2
instruction).
Remote control enrollment:
1. The car alarm should be disarmed, ignition on
2. Send the SMS instruction: MASTER LEARN RC
The siren will chirp 3x and the LED will start flashing.
3. Press and hold buttons A and B together for 3 sec on the remote control.
A siren chirp confirms the enrolment.
By enrolling the first remote control all other remote controls
previously enrolled will be erased (all the remote controls you want to
use must be enrolled during the same enrolment session).
4. Exit enrollment by turning the ignition off.
Wireless detector enrollment:
1. The car alarm should be disarmed, ignition on
2. Send the SMS instruction: MASTER LEARN JA
The siren will chirp 3x and the LED will start flashing.
3. Insert a battery in to the detector.
A siren chirp confirms the enrollment.
By enrolling the first detector all other detectors previously enrolled
will be erased (all the detectors you want to use must be enrolled
during the same enrollment session).
4. Exit enrollment by turning the ignition off.
Note: if the detector is switched to delay mode the alarm will provide a 20
second entrance delay after triggering of the detector. An exit delay of 20
seconds is provided to all enrolled detectors after the car alarm arming.
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Jablotron CA-1202 - mode 2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Jablotron CA-1202 - mode 2 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,63 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Jablotron CA-1202 - mode 2

Jablotron CA-1202 - mode 2 Gebruiksaanwijzing - English - 2 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info