30140
6
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
7. Programming mode
The programming menu allows you to change from one model memory to another and
adjust the settings required to set up your vehicle. The programming mode screens will
appear in the following order:
1. Model select
2. Sub-Trims
3. EPA
4. Exponential
5. ABS
6. Mixing
Programming
- Access the menu by holding the "FUNC" (function) button down while the transmitter is already on.
A) Model Select
- Press the "DATA" + or - buttons to select the model to be used. (1-20)
- Note: Be aware that if you wish to name or re-name a model, you will need to select the model,
exit the menu or turn the radio off, and then follow the model naming instructions in the main edit mode.
- Press the "FUNC" button to scroll to the next menu.
B) Sub-Trims
- After entering the programming mode press the "FUNC" button to scroll to the sub-trim menu.
- The current settings will show on this menu, if you wish to change them press the "SEL" button.
- "Steering" will appear first. Use the "DATA" + and - buttons to adjust the sub-trims right and left.
- Press the "SEL" button to access the throttle sub-trim and adjust with the "DATA" + or - buttons.
- Press the "SEL" button to access the auxiliary 3rd channel sub-trim and adjust with the
"DATA" + or - buttons.
- Press the "SEL" button to loop back to the main sub-trim menu.
- Note: The main sub-trim menu will now show all the new settings.
- Note: Push the "DATA" + & - buttons at the same time to reset to factory default.
- Press the "FUNC" button to scroll to the next menu.
C) EPA (End Point Adjustment)
- After entering the programming mode press the "FUNC" button to scroll to the EPA menu.
- The current settings will show on this menu, if you wish to change them press the "SEL" button.
- "Steering" will appear first. Use the "DATA" + button to adjust the EPA setting higher or
the - button to adjust it lower.
- Note: leaving the steering wheel in the center will adjust both Left and Right at the same time.
TO ADJUST EACH SIDE INDIVIDUALY move the wheel in the direction you wish to set.
- Tip: Always max out the dual rate dial to 125% before setting your individual end points for
maximum travel.
- Tip: When setting the EPA, turn and hold the steering wheel to the end then increase or decrease the
EPA so that the servo moves the wheels on the car to their maximum travel without binding.
- Tip: Reset the total time timer when you recharge or replace your batteries so you can
estimate how much run time they will have left.
- Press the "FUNC" button to scroll to the next menu.
G) 3rd Channel Switch Select
- After entering the main edit mode press the "FUNC" button to scroll to the
3rd channel switch select menu.
- Push the "DATA" + and - buttons to select either "Linear" or "Shift".
- Linear is activated via the trim tab on the right side of the steering column and can be moved to
any position you select. This is typically used for mixture control in nitro boats, but you can use it for
anything else you can think of too.
- Shift is activated by the momentary button located to the lower left of the steering wheel.
This is used to shift vehicles such as the T-Maxx or similar type products.
- Tip: Use the knuckle of your left thumb to push the button to shift.
When the button is pushed the AUX servo will travel to
one end, then when it is pushed again, it will travel to the other end.
Each end point can be set in the EPA screen in the
programming mode for fine tuning.
- Press the "FUNC" button to scroll to the next menu
H) Exit
- Once you have set all the parameters in this menu you can exit by
simply turning the radio off, and then back on again to operate.
- If there is still more programming needed push the "FUNC" button to
scroll through the menu again.
- Scrolling is only in one direction so if you miss a screen just go around
until you get back to the screen you want.
Steering
0
Throttle
0
Auxiliary
0
Steering Throttle Auxiliary
L100% R100% F100% B100% +100% -100%
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitec AGGRESSOR_CRX bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitec AGGRESSOR_CRX in de taal/talen: Engels als bijlage per email.

De handleiding is 0,93 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info