30140
5
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
E) Servo Reversing
- After entering the main edit mode press the "FUNC" button to scroll to the servo reversing menu.
- Press the "SEL" button to move the curser to select ST for steering, THRO for throttle or
AUX for the third auxiliary channel.
- Once the proper channel is selected, press the "DATA" + and - buttons at the same time to
reverse the servo.
- If properly done you will hear one "beep" and the solid square icon will move from
"NOR" (Normal) to "REV" (Reverse) or vice versa.
- Press the "FUNC" button to scroll to the next menu.
This menu allows you to set up your model with the settings you will only need to
assign once. You will typically not need to access this menu unless setting up a
new model. The main edit mode screens will appear in the following order:
1. Model Naming
2. Model Copy
3. Model Reset
4. Servo Reversing
5. Timer
6. Ch #3 Switch Set
6. Main Edit mode
A) Entering the Main Edit Mode
- Access the menu by holding the "FUNC" (function) button down while turning the
transmitter power switch on at the same time.
- The model naming should appear if it done right. Repeat the procedure if it does not.
Programming
F) Timer
- After entering the main edit mode press the "FUNC" button to scroll to the timer menu.
- Press the "SEL" button to move the curser to select minutes or seconds.
- Press the "DATA" + or - buttons to select the time you wish to count down to,with a max of 59:59 or
set it to 00:00 to count up.
- To activate the timer when using the radio, push the "SEL" button.
- To pause the timer, push the "SEL" button again, and then push it again to restart.
- To cancel the timer, push the "FUNC" button.
- To reset the total time on the timer, push the "DATA" + and - buttons at the same time.
- Note: The number that appears in the same place where the timer is displayed is the total time in
hours and minutes that the transmitter has on since it was last reset.
D) Model Reset
- After entering the main edit mode press the "FUNC" button to scroll to the model reset menu.
- To reset the model you are programming, press the "DATA" + and - buttons at the same time to
complete the reset procedure.
- If properly done you will hear two "beeps".
- Note: If you do not hear the double beep then try again.
- Be aware that all the setting will be reset to factory default so anything previously set will be lost.
- Press the "FUNC" button to scroll to the next menu.
B) Model Naming
- Press the "DATA" + or - buttons to select the proper letter or symbol.
- Press the "SEL" (select) button to move the curser.
- After the name is set, press the "FUNC" button to scroll to the next menu.
- Note: Be aware that you have to select the model you wish to name in the Programming mode first.
C) Model Copy
- After entering the main edit mode press the "FUNC" button to scroll to the model copy menu.
- The master is the model currently selected in the programming mode.
- The slave can be any model you choose, but be aware it will overwrite any existing
programming so be careful not to wipe out a model you have already set up.
- Press the "DATA" + or - buttons to select the slave model you wish to copy to.
- Once the slave model is selected, press the"DATA" + and - buttons at the same time to complete
the copy procedure.
- If properly done you will hear two "beeps".
- Note: If you do not hear the double beep then try again.
- Press the "FUNC" button to scroll to the next menu.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitec AGGRESSOR_CRX bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitec AGGRESSOR_CRX in de taal/talen: Engels als bijlage per email.

De handleiding is 0,93 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info