30140
4
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
5 Receiver Servo Connections
4. Recharging Batteries
Alkaline or
rechargable "AA"size
Battery Cover
Battery Case
 
  
7.2V
 
   
 
 



  

Elecric Car Installation
ESC
RECEIVER
CH1
CH2
Nicad Battery
Battery Holder
Battery Cover
Individual cell Battery Installation Nicad Battery Installation
- Connect the included Hitec CG-25 overnight wall charger to the transmitter
charging jack located under the switch to charge.
- Note: If the charger is properly hooked up to the transmitter, the red light on the charger
will be lit while charging. If the red light does not glow, check the connection or the battery.
- The CG-25 can also charge a 4 cell Nicad receiver battery through the
second output pigtail connected to the switch harness.
- Note: If the charger is properly hooked up to the receiver battery, the green light on the charger
will be lit while charging. If the green light does not glow, check the connection or the battery.
- A full charge on the supplied transmitter Nicad battery pack will take 12-16 hours.
- Warning: Do not attempt to charge alkaline batteries or they may explode.
A) Receiver
- DCX dual conversion.
- You can use a separate receiver 4.8v - 6V battery pack if required for your particular model.
This battery is typically only used with a gas or nitro powered vehicle to supply power to the receiver.
Connect as shown.
- Note: If using an electronic speed control, it will supply the power to the
receiver through the connector plugged into channel #2.
- Be aware you should keep your receiver antenna at least 2" away from
any power wires to prevent potential interference.
- Route the antenna up an antenna tube as typically shown in your vehicles instructions.
- Warning: Be sure not to cut off any excess antenna wire, as it will shorten your operating range.
B) Servos
- The HS-325HB heavy duty gear, ball bearing servo is only include with the standard version systems
part#127271 and #127751. All other sytems come without servos. See the included list for reference.
- Note: Always use the proper servo for your application. Using a servo that is not powerful enough
can damage it and your vehicle could potentially go out of control.
- When installing the servos, refer to the manual of the vehicle for proper installation.
- Once your servos are correctly installed, make sure they are properly centered. To do this,
remove the servo horns, turn on your transmitter, then switch on the power to your receiver.
- Note: Remember; always turn your transmitter on first and off last. Failure to do so may result in
loss of control and damage to your servos and/or linkage.
- Now that the power is on check that the servos are working properly.
- Center the trims and sub-trims, and then replace the horns so that they are centered.
- Be aware they may not be perfectly centered; this is OK, just get them as close as possible,
and then use the trims or sub-trims for fine-tuning.
C) Battery
- The AA receiver battery holder supplied with your radio should be used in a non-electric vehicle
requiring two servos.
- Connect the AA receiver battery holder to the power switch supplied or an optional 4-5 cell Nicad or
NiMh pack to the optional #57215S power switch, and then plug the switch harness into the
"Batt" channel of the receiver for power.(See illustration)
- You will not need this battery if you are using an electric car with an electronic or mechanical
speed control with BEC.
Ok! Now let's get to the programming!
   
 
Gas/Nitro Car Installation
RECEIVER
CH1
CH2
BATT

4.8~6.0V
Note: Only one battery should be
connected at a time.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitec AGGRESSOR_CRX bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitec AGGRESSOR_CRX in de taal/talen: Engels als bijlage per email.

De handleiding is 0,93 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info