665714
5
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
This equipment must be used and stored in a place protected from dust, acid, gas or any other corrosive substance.
Attention: this equipment does not comply with the standard IEC61000-3-12. If the machine is connected to the
public network on low voltage, the installer and operator must ensure that the machine can be connected - consult
your power supplier if necessary.
In order to reduce possible electromagnetic disturbances, you can:
Install electric filters close to the socket in case of excessive conducted disturbances. The earth and torch cables
should be as short as possible and be placed close together as far as possible from any other cable, power tool or
electrical cables.
The electromagnetic fields can disturb other equipment, eg; pacemaker or hearing aid.
People wearing pacemakers are advised to consult their doctor before using this device.
Do not use the welding unit to thaw pipes.
Handle gas cylinders with care. There is increased danger if the bottle or it's valve are damaged.
Electric and magnetic fields may interfere with netwok cables and may cause disturbances.
Never wrap the welding leads around your body. Do not place your body between the earth and the torch cable,
they should be placed on the same side.
Electromagnetic disturbances should be reduced as much as possible if they disturb the operator's activity. The
operator is responsible for the installation and the use of the welding equipment and should seek advice from the
manufacturer if required.
Electric wiring rule to reduce disturbances
It is sometimes useful to set all the parts at the same voltage (while respecting the standards in place for each).
Installing an earth connection to the workpiece may reduce the disturbances, and will not increase the risk to the
operator or any other electrical appliances.
The shielding of the welding cables and of any other cables may be useful.
IP protection
IP23S
- Protection prevents access to hazardous parts with fingers or other solid foreign bodies with a diameter equal to or
higher than 12.5mm
- Protective grid - against rain fall at an angle of 60°.
- Case protects against effects of water/dust penetration when the equipment is not in use.
Set up
Only qualified personnel authorized by the manufacturer should perform the installation of the welding equipment.
During set up, the operator must ensure that the machine is unplugged. The serial or parallel connections on a
generator are prohibited.
Transportation of the machine
Two handles are fitted on the equipment to carry it easily, be careful to not underestimate its weight.
This machine is not equipped with a lifting fascility - the operator is required to make the necessary arrangements
for safe lifting and transport of the machine (be careful not to tilt the machine).
Do not use the cables or torch to move the machine. The welding equipment must be moved in an upright position.
Never lift the machine while there is a gas cylinder on the support shelf - follow the separate movement guidelines
specified for the gas bottle.
The removal of the wire reel from the machine is recommended before undertaking any lifting operation.
Setting up the machine
Rules to follow:
¤ Put the machine on the floor (maximum incline of 15°.)
¤ Ensure the work area has sufficient ventillation for welding, and that there is easy access to the control panel.
¤ The machine must be placed in a sheltered area away from rain or direct sunlight.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gys TIG 250 AC-DC bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gys TIG 250 AC-DC in de taal/talen: Engels als bijlage per email.

De handleiding is 1,09 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info