665714
6
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
DESCRIPTION
Thank you for choosing this machine! To get the best use from your machine please read the following carefully.
The TIG 250 AC/DC is a portable, single phase, ventilated Inverter welding unit to be used with non consumable
electrode (TIG) in direct (DC) or alternative (AC) current. TIG welding requires a gas shield protection of
pure(Argon). In MMA mode, it allows you to weld with any kind of electrodes: rutile, basic, stainless steel or cast
iron.
The TIG 250 AC/DC can be equipped with a remote control or foot pedal.
The TIG 250 AC/DC has an integrated liquid cooling system to connect liquid cooled torches.
POWER SUPPLY STARTING UP
This machine is delivered with a 5 pin three-phase plug (3P + N + PE) 400V 16A type CEE17. The TIG 250 AC/DC
must be connected to a 400 V socket (50 - 60 Hz) WITH earth protected by a 16A circuit breaker and a 30mA
overcurrent discontactor. The absorbed current (I1eff) is indicated on the device, for its maximum setting.
Check that the power supply and its protection (fuse and/or circuit breaker) are compatible with the
current needed by the machine. In some countries, it may be necessary to change the plug to allow the
use at maximum settings.
This unit has an internal cooling liquid system which has 2 main functions: the cooling of the water torch if
connected and the cooling of internal spare parts. So the tank of the unit needs to be filled to the maximum line
indicated at the back of the machine.
The starting up is made by pushing on the standby button.
The device turns into protection mode if the power supply tension is under 360V or over 440V or if a
phase is missing. To indicate this default, the screen displays. Once in protection mode, you have to
unplug the device and plug it back into a socket delivering the correct voltage (see the table of error
messages).
Fan: in MMA mode, the fan works nonstop. In TIG mode, the fan works only when welding, then stops after
cooling.
These are Class A devices. They are designed to be used in an industrial or professional environment. In a
different environment, it can be difficult to ensure electromagnetic compatibility due to conducted
disturbances as well as radiation
. They comply with the norm CEI 61000-3-12.
DEVICE PRESENTATION (FIG-1)
Screen + potentiometers
+ polarity plug
- polarity plug
Gas connection for torch
Trigger connection
Water input for water cooled torch
Water output for water cooled torch
Remote control connection
5A fuse support
ON / OFF switch
Power cable
Tank
Gas inlet
CONTROL BOARD (IHM) (FIG-2)
The control board is made of a colour TFT screen and two potentiometers. How it works in 3 states:
State 1 or Standby mode: with the potentiometer 1 you will be able to set the welding current, and with the
potentiometer 2 the parameters related to the welding current.
State 2 or Welding mode: by pushing the potentiometer 1 you will have access to the top menu. Then by turning the
button you will select the welding mode. You will exit this menu by waiting 8s or by pushing the potentiometer 2 ->
back to State 1.
State 3 or Welding parameters mode: by pushing the potentiometer 2 you will have access to the welding
parameters and you will see the selection by turning the button. You will exit this menu by waiting 8s or by pushing
the potentiometer 2 -> back to State 1.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gys TIG 250 AC-DC bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gys TIG 250 AC-DC in de taal/talen: Engels als bijlage per email.

De handleiding is 1,09 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info