479887
9
Verklein
Vergroot
Pagina terug
1/9
Pagina verder
To reset the system proceed as follows:
Switch-off power supply
hort-circuit the RED and BLACK wires of the 2-way connector
Switch the on; once the alarm system is powered, 4 acoustic signals will sound and the turn
indicators will flash 4 times
Remove the previously created short-circuit; the status LED lights up steady.
reset is confirmed by an aucoustic signal and the wailing of the siren for
approx. 3 seconds
the LED will turns off. There are no acoustic signals
!
!
!
!
!
!
system .
S LED .
system
.
Turn ignition key “ON”;
.
Turn ignition key “OFF”; .
By activating the following procedure, the system returns to the
Factory default setting.
This procedure must therefore only be used in case of need, before programming the
system or auto-learning the turn indicators flashes.
!
15.0 -
15.1 - CO
15.2 - SENSOR ADJUSTMENT
I
.
T:
.
ULTRASONIC VOLUMETRIC PROTECTION
NNECTION AND POSITIONING
nsert the WHITE connector in the “W” marked socket and the RED connector in the “R” marked
socket (see figure below).
Install the transducers of the ultrasonic sensors on the top part of the windscreen internal pillars, away
from the air vents and orient them towards the center of the rear window
o check sensitivity level proceed as follows
With the alarm system disarmed, roll down the front window about 20 cm.
Adjust trimmer at a medium setting.
Close all doors, bonnet and boot and arm the system.
During the system inhibit arming time introduce an object in the cabin through the window and
move it around; the status LED will turn off to signal a presence.
If sensitity lelvel is too high or too low, readjust the trimmer and repeat the above procedure
!
!
!
!
!
ULTRASONIC
CELLS
CONNECTIONS
SENSITIVITY
ADJUSTMENT
PAGE 16 - INSTALLER MANUAL INSTALLER MANUAL - PAGE 17
17.0 - TECHNICAL SPECIFICATIONS
Power supply
Current absorption @ 12Vdc with system armed and LED flashing
Working range temperature
Turn signals relay contact capacity
Engine immobiliser relay contact capacity
Alarm cycle duration
Maximum positive current output when armed (+A)
Maximum load of siren output
12 Vdc
15 mA
From -30°C to +70°C
8 A at 20°C
8 A at 20°C
30 sec.
700 mA
1A
16.0 - SYSTEM RESET
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gemini 933 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gemini 933 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,6 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Gemini 933

Gemini 933 Gebruiksaanwijzing - Deutsch - 9 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info