479887
6
Verklein
Vergroot
Pagina terug
1/9
Pagina verder
9.0 - VEHICLE CODE PROGRAMMING
I
”.
f the system is to be managed via CAN-BUS line, it must be configured according to the vehicle on
which it is to be installed.
To help you understand the coding procedure, here below is an example illustrating the configuration
procedure.
In this case the code used is 1-0-3 which hypothetically corresponds to a “FIAT XXXXX
e area).
A separate leaflet, included in the alarm packaging, lists all the available vehicles
(codes are updated at packaging time).
Up-to-date information on supported vehicle models can be found at: www.gemini-
alarm.com (privat
!
!
Press the vehicle remote control lock/unlock buttons to make sure the alarm system works
properly.
Eventually disconnect the 8-way connector and reconnect it after few seconds
TEN FLASHES AND
A SHORT PAUSE
THREE FLASHES
ONE FLASH AND A
SHORT PAUSE
Connect the connectors of the wiring harness to the connector of the system.
.Press and hold the button shown below until the LED lights up
Release the button, the LED switches off.
After a 3/4 seconds pause, the LED starts the first sequence of flashes.
Press “1”.the button at the first flash which corresponds to number
After a 4 seconds, the LED starts the second sequence of flashes.
Press “0”.the button at the tenth flash which corresponds to number
After another 4 seconds, the LED starts the third sequence of flashes.
Push the button at third LED flashing, corresponding to value “3”.
When the last digit is entered, the alarm system “repeats” the entered code.
10.0 - SELF-LEARNING OF TURN INDICATORS FLASHES
In order to arm/disarm through the turn indicators, the system must learn the vehicle locking (arming)
and unlocking (disarming) flashes.
Connect the WHITE-ORANGE wire to the turn indicators and proceed as follows
Disconnect the 8-way wiring connector from the 8-way system connector.
Turn ignition key “ON”.
Connect the 8-way wiring connector to the 8-way system connector; the LED turns on steady.
urn ignition key
lose all doors and press the lock button on the original remote control.
When the turn indicators stop flashing, a high-pitched acoustic signal confirms the learning of the
arming flashes.
Press the unlock button on the original remote control.
When the turn indicators stop flashing, 2 high-pitched audio signals confirm the learning of the
disarming flashes.
This completes the procedure
!
!
!
!
!
!
!
:
T “OFF”.
C
.
!
!
To cancel the programming of the turn indicators reset the system (see
chapter 16.0).
Press
Press
Press
FIRST
FLASH
TENTH
FLASH
THIRD
FLASH
3-4 seconds
PAGE 10 - INSTALLER MANUAL INSTALLER MANUAL - PAGE 11
!
The system has an indicator LED that signals any wrong vehicle code inserted.
The code must be range between 100 and 235 otherwise the LED on the unit blinks
repeatedly and the procedure is interrupted.
The previously inserted code remains stored.
The procedure is also invalidated if the LED blinks more than 10 times.
In this case there are no optical warnings, the procedure is simply be interrupted.
In either case, repeat the whole procedure.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Gemini 933 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Gemini 933 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,6 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Gemini 933

Gemini 933 Gebruiksaanwijzing - Deutsch - 9 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info