463800
5
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
echoInstallationInstructions 5

On an echo 200/500c/550c device, the connectors on the cables are keyed to
t only in the correct ports on the cradle. The connected cables are then held
in place by a locking bracket.
No cables connect directly to an echo 200/500c/550c device.
1 Compare the divot
on the cable connector
to the keying on the cradle ports to identify the
correct port.
2. Push the cable connector into the correct port
until it rests rmly in the port.
3. Repeat steps 1 and 2 until all of the
cables are connected to the cradle
.
4. Place the locking bracket
over the
cables and slide it down to lock them
in place on the cradle.
You will hear an audible click when
the locking bracket is correctly
installed.

After you have connected the cables to the cradle, you can quickly place the
echo device in the cradle without plugging in
any cables.
1. Place the base of the echo
in the
bottom of the cradle
.
2. Tilt the echo toward the cradle until it
fastens in place.
You will hear an audible click when the
device is secured in the cradle.


After you have connected the cables to the cradle, you can quickly remove
the echo from the cradle without unplugging any
cables.
1. Press the release lever
on the cradle until
the echo device
is released.
2. Tilt the echo device forward and lift it out of
the cradle.

Notice
Do not leave your boat in the water for an extended period of time without
checking for leaks.
Because water is necessary to carry the sonar signal, the transducer must be
in the water to work properly. You cannot get a depth or distance reading
when out of the water. When you place your boat in the water, check for
leaks around any screw holes that were added below the water line.

Notice
When adjusting the depth of the transducer, make the adjustments in
small increments. Placing the transducer too deep can adversely affect the
performance of the boat and put the transducer at risk of striking underwater
objects.
Test the transom mount transducer installation in open water free of
obstacles. Pay attention to your surroundings as you test the transducer.
1. With the boat in the water, turn on the echo device.
2. Drive the boat at a slow speed. If the echo device appears to be working
properly, gradually increase speed while observing the echo device.
If the sonar signal is suddenly lost or the bottom return is severely
degraded, note the speed at which this occurs.
3. Return the boat to the speed at which the signal was lost, and make
moderate turns in both directions while observing the echo device.
4. If the signal strength improves while turning, adjust the transducer so that
it extends another
1
/
8
in. (3 mm) below the transom of the boat.
5. Repeat steps 2–4 until the degradation is eliminated.
6. If the signal does not improve, move the transducer to a different location
on the transom.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Garmin Echo 100 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Garmin Echo 100 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,71 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Garmin Echo 100

Garmin Echo 100 Installatiehandleiding - Nederlands - 6 pagina's

Garmin Echo 100 Gebruiksaanwijzing - Nederlands - 12 pagina's

Garmin Echo 100 Installatiehandleiding - Deutsch - 6 pagina's

Garmin Echo 100 Gebruiksaanwijzing - Deutsch - 12 pagina's

Garmin Echo 100 Gebruiksaanwijzing - English - 12 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info